علم الصرف العربي المتقدّم لأغراض علمية (دراسة في الفعل وأبنيته وددلالته وأزمنته من خلال شواهد القرآن الكريم)... by Dollah, Nafi@Hanafi

“…To study about alsorf al-Arabi al-mutaqaddim li-aghradh ilmiyyah min khilal al-Quranul karim theoritically and practically…”
Get full text

Statistical analaysis for removal of Cadmium from aqueous solution at High pH by Kabbashi, Nassereldeen Ahmed, Daoud, Jamal Ibrahim, Mirghani, Mohamed Elwathig Saeed, Rosli, Nurhasni Falina

“…From the results obtained, the highest percentage removal of Cd using CNT is at pH7, 10 mg of CNTs dosage, contact time of 120 min and agitation speed of 150 rpm which gave 19.14% removal.…”
Get full text

Prediction of minimum chip thickness in tool based micro end milling by Ali, Mohammad Yeakub, Khan, Ahsan Ali, Mohamad Asharaf, Asfana Banu, Abdul Wahab, Adibah

“…The optimum value for the minimum chip thickness was 375 nm with cutting speed of 2275 rpm, feed rate of 2.6 mm/min, and depth of cut 0.6 μm using Ø 0.8 mm tool. …”
Get full text

BE-P32: fabrication of Nahar Seed Oil for biolubricant production by Mirghani, Mohamed Elwathig Saeed, Kabbashi, Nassereldeen Ahmed, Qudsieh, Isam Y., Ibrahim, Irmanisha

“…From the result obtained, the maximum viscosity of NSO biolubricant was achieved when the temperature was 150oC, 80 min in reaction time and 0.8% catalyst dosage. …”
Get full text

Kajian terhadap faktor-faktor mempengaruhi pencapaian pelajar dalam penilaian menengah rendah di Sabah by Salleh, Mohamad Johdi

“…Hasil dari penganalisisan data ini diterangkan dalam bentuk kekerapan, peratusan dan min. Dapatan kajian menunjukkan bahawa domain kendiri, guru, ibubapa, dan rakan banyak mempengaruhi strategi dan gaya pembelajaran pelajar yang mendorong kepada pencapaian PMR.…”
Get full text

Powder mixed micro electro discharge milling of titanium alloy: Investigation of material removal rate by Ali, Mohammad Yeakub, Abdul Rahman, Nur Atiqah, Mohamad Aris, Erniyati

“…In this experimental investigation, maximum MRR of 7.3 µg/min was obtained for 24.75 g/l SiC powder concentration and 56.77 µJ discharge energy. …”
Get full text

The economic impact of using negative rake angle in high speed hard turning by Al Hazza, Muataz Hazza Faizi, Adesta, Erry Yulian Triblas

“…The experiments were obtained with constant cutting depth (0.15 mm), constant feed rate (0.075 mm), constant cutting speed (250 m/min) and five different tool rake angles0o,-3, -6,-9 and -12). …”
Get full text

Experimental study of cutting parameter for drilling on fabric carbon/epoxy composite laminates by Abd Halim, Nor Farah Huda, , Afzeri, Aminanda, Yulfian

“…Variation of cutting parameter such as feed rate (50,100 and 150 mm/min) and speed(400,800,1200 rpm) were tested in this study. 6 different laminates orientation (0°/0°/0°/0°, 45°/45°/45°/45°, 0°/45°/0°/45°, 45°/0°/45°/0°, 0°/0°/45°/45° and 45°/45°/0°/0°) were tested in order to see which one is the best. …”
Get full text

The evaluation of kLa values for recombinant Escherichia coli fermentation producing β-Glucuronidase enzyme by Mel, Maizirwan, Abdul Karim, Mohamed Ismail, Mohd. Salleh, Hamzah

“…From the four experiments conducted, experimental nul mnnber two with agitation of 300 rpm, airflow rate of 2 vvrn and temperature 41°C generate the highest Optical Density (OD 660 nrn) of 2.313 for cell count and also having an equivalent k,a value of 0.0281 min-lor 1.686 h-1.This condition was fOlllld to be an effective point for upscaling in bigger bioreactor for E. coli fermentation to produce the enzyme.…”
Get full text

Single-route synthesis of magnetic biochar from sugarcane bagasse by microwave-assisted pyrolysis by Mohamed Noor, Noraini, Abdullah, Ezzat Chan, Othman, Raihan, Mujawar, Mubarak N.

“…The optimum conditions for producing high yield 69% magnetic biochar from sugarcane bagasse by microwave heating were 30 min of radiation time and an impregnation ratio (Fe2O3:biomass) of 0.45. …”
Get full text
Get full text

Effects of Multi-Walled Carbon Nanotubes (MWCNTS) on the mechanical and thermal properties of plasticized polylactic acid Nanocomposites by Othman, Maizatulnisa, Tan, Kok Hui, Hashim, Mohd Yusof, Khalid, Halissani, Ghazali, Ruzaidi, Zakaria, Nazarudin, Mat Tahir, Paridah, Hassan, Noor Azlina

“…A multi-walled carbon nanotube (MWCNT)/plasticized polylactic acid (PLA) composite was prepared using a two-roll mill set at 170C and 50 rev/min. The material was characterized using dynamic mechanical analyzer (DMA). …”
Get full text

Parametric study of carbide precipitation in 16% chromium ferritic stainless steel (FSS) welds by Amuda, Muhammed Olawale Hakeem, Mridha, Shahjahan

“…This results in wider ditched-structure in welds made with flow rates lower than 0.052L/min. Cryogenic cooling produces more ditched weld microstructure revealed by electrolytic etching in oxalic acid; however, the structure is acceptable since no single grain boundary is completely surrounded by ditches. …”
Get full text

Investigation of machining parameters for the multiple-response optimization of micro electrodischarge milling by Mehfuz, Reyad, Ali, Mohammad Yeakub

“…The optimized values of Ra, Ry, TWR, and MRR were 0.04, 0.34 μm, 0.044, and 0.08 mg min−1, respectively for 4.79 μm s−1 feed rate, 0.1 nF capacitance, and 80 V voltage. …”
Get full text

The reach, adoption, and effectiveness of online training for healthcare professionals by Webb, Justin, Stockwell, J., Chavez-Ugalde, Y.

“…This short communication reports on evaluation data from delivery of a 60-min online training session to healthcare professionals, between January and November 2016.…”
Get full text

Amalan teknik mengingat di kalangan pelajar-pelajar Sekolah Menengah Teknik Batu Pahat, Johor by Torman, Zaida

“…Data dikumpul melalui kaedah soal selidik dan dianalisis menggunakan taburan frekuensi, peratusan dan skor min. Analisis ini dilakukan menggunakan perisian SPSS for Windows 10.0. …”
Get full text
Get full text
Get full text

المطابقة اللغوية وعلاقتها بالأخطاء اللغوية العربية لدى المتعلمين الماليزيين (al-Mutabaqah al-lughawiyah wa-'alaqatuha bi-al-akhta' al-lughawiyah al-'Arabiyah lada al-muta'allimi... by Masoud, Mahadi, Mohd Shamsudin, Jamsuri, Jalil, Marsufah

Get full text

Efficiency of Ventilator Associated Pneumonia Prevention Protocol in a mixed intensive care unit in Pahang, Malaysia by Mat Nor, Mohd Basri, Abdul Rani, Mohammed Fauzi

Get full text

Noruz: treading time, nature, culture and faith by Zekrgoo, Amir Hossein

“…To this day Noruz is observed in Iran, Afghanistan, parts of Central Asia, Caucasus, South Asia (Indian subcontinent), Northwestern China, the Crimea and some parts in Balkans. Moreover, the festival of Noruz is tightly connected to the cycle of nature and is scientifically regarded as the most accurate mark of the spring equinox, hence the beginning point of a very precise calendar system. …”
Get full text

Modelling the effect of factors on the stated preference towards telecommuting in IIUM campus, Gombak by Ismail, Farah Diyanah, Kadar Hamsa, Abdul Azeez, Mohamed, Mohd Zin

Get full text
Get full text

An analysis of the Dongba arts and culture in the context of tourism by Xie, Zheng

“…This dissertation examines the role of individuals and groups within a specific tourism destination in China in adapting and responding to both government policy and tourism development in the region. …”
Get full text