-
461
Natural dye coated nanocrystalline Tio2 electrode films for DSSCs
Published 2011“…Nanocrystalline TiO2 thin films were successfully prepared by dip-coating technique on ITO conductive glass substrates at low temperature. …”
Get full text
Book Chapter -
462
Tribological behavior of dual and triple particle size SiC reinforced Al0MMCs: a comparative study
Published 2008“…The wear test was carried out using a pin-on-disc type tribo-test machine under dry sliding condition. …”
Get full text
Article -
463
Reverse engineering of automotive piston
Published 2012“…The wear test was performed using pin-on-disk (POD) machine. The tensile test results showed that the ultimate tensile strength and modulus of elasticity of the piston were 215 MPa and 73 GPa respectively, whereas the Vickers hardness number of this material was found to be 155 HV0.5kgf. …”
Get full text
Proceeding Paper -
464
Electronically reconfigurable and conformal triband antenna for wireless communications systems and portable devices
Published 2022“…This is achieved by connecting two open-ended stubs to a modified triangular patch radiator using PIN diodes. The antenna’s performance was optimized using a 3D electromagnetic solver and its performance was verified through measurements. …”
Get full text
Get full text
Article -
465
Numerical construction of piecewise virtual fields
Published 2011“…Such a piecewise construction has been successfully used to characterize a thin composite plate in bending. Moreover, the use of piecewise elements has shown its merits in the characterization of a damaged composite plate. …”
Get full text
Book Chapter -
466
Numerical model of noise effect in full field data
Published 2011“…This chapter discusses the important issue of experimental noise simulation in the formulation of piecewise virtual fields method for the characterization of thin composite plate. In actual practice, the full field data captured through an optical dive on the surface of a specimen is always prone to some noise effect. …”
Get full text
Book Chapter -
467
The effect of milling parameters on laminated carbon fibre reinforced plastic (CFRP)
Published 2012“…A solid uncoated carbide end mill cutting tool and a CFRP panel with fibre orientation of 0/45° were used to investigate the machinability of CFRP composite during milling; a cutting speed of 16 m/min to 240 m/min with a feed rate of 0.0125 mm/tooth to 0.0125 mm/tooth were set. …”
Get full text
Article -
468
-
469
A comparative study of the effectiveness of ca-alginate and k-carrageenan beads as support material for enzyme immobilization
Published 2015“…Michaelis parameters Vmax and KM for Ca-alginate were found to be 65.36 mmol/min and 8.60 mM respectively, and for K-carrageenan 61.73 mmol/min and 0.94 mM respectively, while Michaelis constants for the free enzyme were 70.42 mmol/min and 2.71 mM. …”
Get full text
Get full text
Proceeding Paper -
470
Photocatalytic degradation of triclocarban in aqueous solution using a modified zeolite/TiO2 composite: kinetic, mechanism study and toxicity assessment
Published 2023“…The kinetic study by following Langmuir-Hinshelwood(L-H) model and pseudo first order, the significant constant rate was obtained at pH 11 which was 0.079 ppm/min, 0.75 cm2 of MZTC catalyst loading size achieved 0.076 ppm/min and 5 ppm of TCC initial concentration reached 0.162 ppm/min. …”
Get full text
Article -
471
Faktor yang mendorong kecenderungan pelajar kolej vokasional ke arah bidang keusahawanan
Published 2014“…Dapatan menunjukkan skor min bagi faktor kemahiran, sikap dan latar belakang pendidikan pada tahap tinggi iaitu masing-masing 4.02, 4.04 dan 3.93. …”
Get full text
Get full text
Thesis -
472
Ciri-ciri yang mempengaruhi pelatih aliran kemahiran untuk menjadi seorang usahawan : satu tinjauan di Institut Kemahiran Mara Lumut, Manjung Perak
Published 2003“…Data-data kajian dianalisa dengan menggunakan program SPSS Versi 11.0 for windows dan dianalisis daripada soal selidik ke dalam bentuk min dan frekuensi. Keseluruhan hasil kajian menunjukkan bahawa pelatih-pelatih mempunyai ciri-ciri keusahawanan yang tinggi berdasarkan skor min keseluruhan (skor min = 4.06). …”
Get full text
Get full text
Get full text
Thesis -
473
-
474
Production of single cell anode-supported SOFC using NiO/YSZ-YSZ-LSM/YSZ powder materials
Published 2015“…The results demonstrated that the thin SOFC single cell was successfully obtained. …”
Get full text
Get full text
Thesis -
475
Application of Virtual Fields Method to Composite Plate Bending Problem
Published 2011“…This chapter discusses the application of virtual fields method to the case of a thin composite plate in bending. The idea is to use the formulation of virtual fields defined over the specimen such that a single carefully designed test can lead to direct identification of all the six unknown bending rigidities. …”
Get full text
Get full text
Book Chapter -
476
Design of a low bit rate STDM multiplexing
Published 2011“…A low bit rate STDM multiplexer architecture design for thing route channels is provided in this chapter. A thin route communication channel is able to transmit 64Kbps to 128Kbps. …”
Get full text
Book Chapter -
477
-
478
How to assess ankle osteoarthritis: comparison of the Kellgren and Lawrence scale with functional outcome and digital image analysis
Published 2012“…Functional outcome was assessed with the AOFAS Hindfoot score. Bone density and minJSW were measured using a previously validated Ankle Image Digital Analysis software (AIDA). …”
Get full text
Article -
479
-
480
Mas Cotek (Ficus deltoidea): a possible supplement for Type II Diabetes: (a pilot study)
Published 2011Get full text
Book Chapter