-
701
Strain rate effect on the failure strain and hardness of metallic armour plates subjected to high velocity projectile impact
Published 2006“…At the same loading rates the plate thinning of steel was recorded to be severe than copper. …”
Get full text
Article -
702
Studies of InAs and GaAs layers prepared by molecular beam epitaxy
Published 1980“…This thesis describes a study of the growth and doping of single crystal thin films of GaAs and InAs by the technique of molecular beam epitaxy (MBE). …”
Get full text
Thesis -
703
Diffusion problems in lead-tin overlay bearings
Published 1984“…The most common barrier is a thin electro-deposit of nickel. Claims have been made that this nickel barrier retards the growth of intermetallic compounds. …”
Get full text
Thesis -
704
Numerical analysis on the anode active thickness using quasi-three-dimensional solid oxide fuel cell mode
Published 2023“…Also, a thick electrode and a high average current density result in a thin active thickness…”
Get full text
Article -
705
Numerical analysis on the anode active thickness using quasi-three-dimensional solid oxide fuel cell model
Published 2023“…Also, a thick electrode and a high average current density result in a thin active thickness.…”
Get full text
Article -
706
Numerical analysis on the anode active thickness using quasi-three-dimensional solid oxide fuel cell model
Published 2023“…Also, a thick electrode and a high average current density result in a thin active thickness.…”
Get full text
Article -
707
Design of microstrip antenna based on different material properties
Published 2015“…These type of antenna are light weight, low volume and thin profile configurations, which can be made conformal. …”
Get full text
Get full text
Get full text
Thesis -
708
-
709
-
710
-
711
-
712
Characterization and solvent stability of strep-tagged purified recombinant lipase from thermostable and solvent tolerant Bacillus sp. strain 42.
Published 2009“…Based on solvent stability studies in 30 min pre-incubation in 25% v/v solvents with a shaking rate at 150 strokes per min, the purified Lip 42 showed a different residual activity profiles depending on solvents and temperatures. …”
Get full text
Article -
713
Wear analysis of Silicon Nitride (Si3N4) cutting tool in dry machining of T6061 Aluminium Alloy
Published 2013“…Machining was performed at four different cutting speeds; 292, 388, 518 and 689 m/min using two different cutting parameters (feed rate, f = 0.2 mm/rev, depth of cut, d = 0.1 mm and f = 0.4 mm/rev, d = 0.2 mm). …”
Get full text
Article -
714
Bladder scan vs urethral cathetarization for measurement of immediate post partum bladder volume
Published 2011“…The mean for time interval between bladder scan and catheterization was 3 min(range between 1-8 min). There is a linear relationship between the bladder scan-estimated and catheter bladder volumes (r2=082). …”
Get full text
Get full text
Get full text
Proceeding Paper -
715
Effect of electrical parameters on performance of Cu-TiC mixed ceramic compact electrode in EDM process
Published 2013“…The highest MRR of 9.93mg/min was obtained with the current of 6.5A and pulse duration of 7.5 μs. …”
Get full text
Get full text
Get full text
Proceeding Paper -
716
Extraction and characterization of gelatin from camel skin (potential halal gelatin) and production of gelatin nanoparticles
Published 2020“…Central composite design combined with response surface methodology was used to achieve high gelatin yields under different extraction conditions: temperatures of 40, 60, and 80 °C; pH values of 1, 4, and 7; and extraction times of 0.5, 2.0, and 3.5 min. Maximum gelatin yield from camel skin (29.1%) was achieved at 71.87 °C and pH 5.26 after 2.58 min. …”
Get full text
Get full text
Article -
717
-
718
-
719
-
720