-
221
An investigation of defect formation and growth in epoxy resin using light scattering methods
Published 1989“…The later has been attributed to failure occurring at the pin tip epoxy interface causing relaxation in the scattering volume. …”
Get full text
Thesis -
222
Multi-Mode Yagi Uda Patch Array Antenna With Non-Linear Inter-Parasitic Element Spacing
Published 2023“…Applying the inter-parasitic element spacing’s optimization and minimizing the switching circuitry using four RF PIN diodes on the parasitic elements have contributed to the gain achievement of more than 7 dBi.…”
Get full text
Article -
223
Innovative UWB phase shifters using groove gap-waveguide technology inspired by metasurfaces for beamforming networks operating at 100 GHz
Published 2025“…The metasurface features a "bed-of-nails" structure, where metal pins are connected to a bottom layer and spaced <λ/4 from a top plate. …”
Get full text
Conference or Workshop Item -
224
Metamaterial based ultra-wideband antennas for portable wireless applications
Published 2017“…Various approaches have been reported to reduce the physical size of RF antennas including using high permittivity substrates, shorting pins, reactive components, and more recently, metamaterials (MTM) based on composite right-/left-handed transmission-lines (CRLH-TLs). …”
Get full text
Book Section -
225
Wear characteristics of Fe-C-Si and Fe-C-Al cast irons
Published 2011“…In the present study, wear behavior of the Fe-C-Si and Fe-C-Al cast irons were investigated using a pin-on-disk type apparatus at room temperature. …”
Get full text
Article -
226
Low-loss paper-substrate triple-band-frequency reconfigurable microstrip antenna for sub-7 GHz applications
Published 2023“…In this paper, a low-cost resin-coated commercial-photo-paper substrate is used to design a printed reconfigurable multiband antenna. The two PIN diodes are used mainly to redistribute the surface current that provides reconfigurable properties to the proposed antenna. …”
Get full text
Get full text
Article -
227
The tribological behaviour of Fe-C-Al cast iron – effect of temperature
Published 2013“…Purpose - The aim of this paper is to study the tribological behaviour of Fe-C-Al cast iron at different temperatures using universal pin-on-disk machine. Design/methodology/approach - The cold set resin bonded sand mould casting process was employed to develop Fe-C-Al cast iron and Fe-C-Si cast iron. …”
Get full text
Article -
228
A study of touching behavior for authentication in touch screen smart devices
Published 2016“…Due to increasing demand for safer access in touch screen mobile phones, old strategies like pins, tokens, or passwords have failed to stay abreast of the challenges. …”
Get full text
Get full text
Proceeding Paper -
229
Ballistic impact fracture behaviour of continuous fibre reinforced al-matrix composites
Published 2010“…The materials response under high energy impact loads was studied using a gas gun. The projectiles were pins 1.2-1.5 mm in diameter and weighing 0.347-0.435 g. …”
Get full text
Article -
230
On phase separation points for one-dimensional models
Published 2009“…In the paper, the one-dimensional model with nearest-neighbor interactions In, n ∈ Z, and the s pin values ±1 is considered. It is known that, under some conditions on parameters of In, a phase transition occurs for this model. …”
Get full text
Article -
231
Measurement and modelling of operational amplifier power supply rejection
Published 1995“…Measured results for 741 and pin-compatible operational amplifiers are tabulated. …”
Get full text
Article -
232
Performance analysis of two packet scheduling algorithms in downlink 3GPP LTE system
Published 2010Get full text
Get full text
Proceeding Paper -
233
Distraction osteogenesis over intramedullary nail : a report of two cases
Published 2006“…The healing index was 19.5 days/cm and 14.8 days/cm respectively, compared favorably to 30 days/cm with traditional method of distraction osteogenesis. There were mild pin tract infections and joint stiffness which responded to non-operative treatment.…”
Get full text
Article -
234
Photonic controlled metasurface for intelligent antenna beam steering applications including 6G mobile communication systems
Published 2023“…This paper presents a novel metasurface antenna whose radiation characteristics can be remotely controlled by optical means using PIN photodiodes. The proposed reconfigurable antenna is implemented using a single radiating element to minimize the size and complexity. …”
Get full text
Get full text
Article -
235
Characterisation of surface texture using AFM with trimmed probe tip
Published 2006“…A comparison of the scanning results with analytical calculation showed that the trimmed tips were superior in imaging the profile for both the hole shaped and pin shaped microfeatures. But when using the trimmed high aspect ratio tip, the scanning speed was significantly low. …”
Get full text
Article -
236
Requirement of handover modeling in the downlink 3GPP long term evolution system
Published 2010Get full text
Get full text
Proceeding Paper -
237
Sensory-based colour sorting automated robotic cell
Published 2005“…The aim of this research work is to recognize colour by pin point detection and sorting of object specimens with respect to their colour attributes, which includes hue, saturation and luminance level. …”
Get full text
Article -
238
Design and Implementation of Active Antennas for IoT-Based Healthcare Monitoring System
Published 2024“…Two dual-band (2.4 GHz and 5.8 GHz) microstrip patch antennas, one with a PIN diode and one without, are fabricated using Rogers Duroid RO3003™ substrate. …”
Get full text
Article -
239
Design and Implementation of Active Antennas for IoT-Based Healthcare Monitoring System
Published 2024“…Two dual-band (2.4 GHz and 5.8 GHz) microstrip patch antennas, one with a PIN diode and one without, are fabricated using Rogers Duroid RO3003™ substrate. …”
Get full text
Article -
240
Design and Implementation of Active Antennas for IoT-Based Healthcare Monitoring System
Published 2024“…Two dual-band (2.4 GHz and 5.8 GHz) microstrip patch antennas, one with a PIN diode and one without, are fabricated using Rogers Duroid RO3003™ substrate. …”
Get full text
Article