GPS-based attitude determination and applications by Xia, Peiqing

Get full text

Laser metal deposition of low carbon 410L stainless steel and heat treatment by Zhai, Wengang, Wu, Naien, Zhou, Wei

“…The yield strength is 601.9 MPa for as-built condition and 930.6 MPa for heat-treated condition (1000 °C/10 min); the ultimate tensile strength (UTS) is 923.0 MPa for as-built condition and 1101.5 MPa for the heat-treated condition (1000 °C/10 min); the elongation is 17.7% for as-built condition and 15.1% for the heat-treated condition (1000 °C/10 min). …”
Get full text

Dose response effect of carbohydrate mouth rinse on 10 km running time trial by Muhammad Saufy Abdul Karim

“…Results: No significant difference (p = .441) in 10 km running time trial were observed between 6.4% CHO [mean 63.83 (SD 11) min] and 15% CHO [mean 65.91 (SD 13.36) min]. No significant difference were found in HR (p = .440) between 6.4% CHO [mean 162 (SD 7) beats/min] and 15% CHO [mean 158 (SD 13) beats/min]. …”
Get full text

Pengetahuan, Sikap dan Praktis (KAP) Komuniti Pekebun Kecil Koko (KPKK) berkaitan Malaysian Good Agricultural Practices (MyGAP) by Noviatin Syarifuddin, Jasmin Arif Shah, Asnarulkhadi Abu Samah, Nik Ahmad Sufian Burhan

“…Tahap amalan pertanian baik (APB) menunjukkan nilai min tertinggi oleh praktis (min 4.20). Diikuti, dengan tahap sikap (min 4.08) dan tahap pengetahuan (min 4.01) oleh KPKK. …”
Get full text

Mechanical properties of pultruded Kenaf fibre-reinforced vinyl ester composites by Abd Manab, Mohd Fairuz

“…The investigation of the effect of pulling speed on the mechanical properties of pultruded kenaf composites shows the optimal pulling speed for tensile strength and compressive strength is 0.3 m/min, tensile modulus 0.1 m/min, flexural strength 0.4, flexural modulus 0.2 m/min. …”
Get full text

Influence of machining parameters and tool geometry on tool wear during cobalt chromium-molybdenum micro drilling by Abdul Patar, Mohd. Affifudin, Suhaimi, Mohd. Azlan, Sharif, Safian, Amrifan S. Mohruni, Amrifan S. Mohruni, Hisam, Muhammad Juzaili, Shaharum, Mohd. Sallehuddin

“…The cutting speeds of 50 m/min, 65 m/min, and 80 m/min were varied. A total of 11 runs were performed, with each run consisting of drilling 30 holes. …”
Get full text

Fabrication of polydimethylsiloxane (PDMS) microarray devices using spin coating by Tan, Doyle Poh Choon

Get full text

Low power PWM based sensor readout circuit by He, Shengyu

Get full text

Characterization of copper chemical mechanical polishing induced defects by Teo, Tai Yong.

Get full text

Interactive analog filter learning tool by Maung Htun Htun Naing.

Get full text

Kinetics of papaya pectinesterase by Fayyaz, A., Asbi, B.A., Ghazali, H.M., Che Man, Y.B., Jinap, S.

“…The activity was linear up to 20 min with an enzyme concentration of up to 6.14 μg. …”
Get full text

Banks regulatory reforms in Singapore. by Foo, Cindy Ping Ping., Lee, Shirleen Sok Loon., Ng, Mui Chee.

Get full text

Studies of wafer level electromigration test for ULSI by Sum, Heng Keong.

Get full text

Design of insulated gate bipolar transistor using novel structure by Zhang, Guowei

Get full text

Recognition of human hand gestures and its application to human-robot interaction by Yin, Xiaoming.

Get full text

State space predictive control of inverted pendulum by Yong, Tet Leong.

Get full text

Multivariable predictive control of a distillation column by Cai, Yue Bin

Get full text

Lying and rumination time as predictors of subclinical ketosis, metritis, and hypocalcaemia in dairy cows during the periparturient period: A systematic review and meta-analysis by Sadiq, Mohammed B., Zaini, Syamira-Syazuana, Shaik Mossadeq, Wan Mastura, Ramanoon, Siti Zubaidah, Syed-Hussain, Sharifah Salmah

“…Meanwhile, the MD of RT was significantly different in both periods (MD = −61.76 and −73.33 min/day, P < 0.05) for SCK and during the prepartum for metritis (MD = −23.37 min/day, P = 0.04). …”
Get full text

Compressive strength of cemented sand by Chong, Ying Jie.

“…In this paper, the four main factors affecting the compressive strength of cemented sand will be investigated: water-cement ratio of 0.5, 0.6, 0.7; sand-cement ratio of 4.0, 5.0, 6.0; curing age at 3, 7 and 28 days; strain rate of 0.5mm/min, 1.0mm/min, and 2.0 mm/min. The other factors such as dry density, sample dimensions (height and diameter), curing conditions were kept constant. …”
Get full text

Se7en : stories of Singapore. by Cheng, Xinhui., Luo, Serene Qingzhi.

Get full text