Showing 1,361 - 1,380 results of 11,283 for search '((sspingge OR ((fine OR line) OR five)) OR (((fins OR (spins OR siens)) OR ling) OR pin))', query time: 0.22s Refine Results
  1. 1361
  2. 1362
  3. 1363
  4. 1364
  5. 1365
  6. 1366

    Macroscopic assembled graphene nanofilms based room temperature ultrafast mid-infrared photodetectors by Peng, Li, Liu, Lixiang, Du, Sichao, Bodepudi, Srikrishna Chanakya, Li, Lingfei, Liu, Wei, Lai, Runchen, Cao,Xiaoxue, Fang, Wenzhang, Liu, Yingjun, Liu, Xinyu, Lv, Jianhang, Abid, Muhammad, Liu, Junxue, Jin, Shengye, Wu, Kaifeng, Lin, Miao-Ling, Cong, Xin, Tan, Ping-Heng, Zhu, Haiming, Xiong, Qihua, Wang, Xiaomu, Hu, Weida, Duan, Xianfeng, Yu, Bin Yu, Xu, Zhen, Xu, Yang, Gao, Chao

    Published 2023
    “…The assembled Schottky diode works in 1.5–4.0 μm at room temperature with fast response (20–30 ns, rising time, 4 mm2 window) and high detectivity (1.6 × 1011 to 1.9 × 109 Jones from 1.5 to 4.0 μm) under the pulsed laser, outperforming single-layer-graphene/silicon photodetectors by 2–8 orders. …”
    Get full text
    Journal Article
  7. 1367
  8. 1368
  9. 1369

    Design and investigation of air-cooled heat sinks using 3D printing technology by Lim, Ming Chong

    Published 2016
    “…The five heat sinks vary in their pin fin cross-section, with two common designs, the circular pin fin and rounded rectangular cross-section pin fin, and three novel designs which consist of a NACA-0024, a NACA-4424 and also a NACA-4424 rotated at a 5° angle of attack. …”
    Get full text
    Final Year Project (FYP)
  10. 1370

    Convective boiling and condensation in enhanced tubes produced by selective laser melting by Tan, Choon Yong

    Published 2018
    “…The design of the four tubes are five long circumferential pin fins, eight short circumferential pin fins, twisted pin fins and a metallic foam structure. …”
    Get full text
    Final Year Project (FYP)
  11. 1371
  12. 1372

    Study of heat transfer through micro-structured surfaces by Chin, Wei Hao

    Published 2016
    “…Each chip has a different microstructure in the form of very small and elongated pin-fins, which will in turn affect the critical heat flux of each component. …”
    Get full text
    Final Year Project (FYP)
  13. 1373

    Experimental studies of melting PCM in a heat sink by Muhammad Azrin Sa'ad.

    Published 2011
    “…The heat sink design that was the focus of this study is based on the pin finned heat sink design. Experiments mainly pertaining to the characteristics of the melting PCM in the heat sinks were observed and recorded to further understand the behaviours and characteristics of the melting PCM. …”
    Get full text
    Final Year Project (FYP)
  14. 1374
  15. 1375

    Effect of curvature variations on the hydrodynamic performance of heaving and pitching foils by van Rees, Wim M.

    Published 2024
    “…Maximum efficiency is achieved when camber is applied during the first half of the stroke, tilting the force vector to create thrust earlier in the cycle than a comparable rigid fin. Overall, our results demonstrate that curving fins are consistently able to significantly outperform rigid fins with the same chord line kinematics on both thrust and hydrodynamic efficiency.…”
    Get full text
    Article
  16. 1376

    Thermal energy storage enhancement of latent heat thermal energy storage systems by Low, Zheng Hua

    Published 2025
    “…With respect to horizontal fins, positively inclined fins of +15º and +30º delayed the full melt time by 3.8% and 4.0%, respectively, while negatively inclined fins at -15º and -30º improved the melt fraction difference by up to 5.2%. …”
    Get full text
    Thesis-Doctor of Philosophy
  17. 1377

    Experimental and numerical studies on the cooling of mobile device by Setoh, Guojing.

    Published 2009
    “…The first one is without fins, second one with three fins and the last one with six fins. …”
    Get full text
    Final Year Project (FYP)
  18. 1378

    Fabrication of heat sinks by Selective Laser Melting for convective heat transfer applications by Wong, Kin Keong, Ho, Jin Yao, Leong, Kai Choong, Wong, Teck Neng

    Published 2021
    “…Three heat sinks comprising pin fins of circular, rectangular-rounded and aerofoil geometries were fabricated by SLM from aluminium alloy AlSi10Mg powder. …”
    Get full text
    Journal Article
  19. 1379

    Celebrating creation : therapeutic use of art and design for the elderly. by Lim, Dorothy Ghim Woon.

    Published 2012
    “…Pablo Picasso once said, “Art washes from the soul the dust of everyday life”. As the world spins faster and faster, modernisation calls for the fast and new, while the old often gets left behind. …”
    Get full text
    Final Year Project (FYP)
  20. 1380

    Analysis and control of aquatic locomotion on robotic fish by Eric Purnama

    Published 2014
    “…In this project, the author developed biomimetic shark, whose swimming mechanism is categorized under thunniform, one of the most efficient swimmers. All four main shark fins were applied in the robot, namely Caudal fin, Pectoral fins, and Dorsal fin. …”
    Get full text
    Final Year Project (FYP)