-
1
Biocementation of fine-grained soil
Published 2017“…Further studies are required to understand the mechanisms of the MICP treatment for fine-grained soil.…”
Get full text
Final Year Project (FYP) -
2
Full-spectrum out-of-distribution detection
Published 2023“…In this paper, we take into account both shift types and introduce full-spectrum OOD (F-OOD) detection, a more realistic problem setting that considers both detecting semantic shift and being tolerant to covariate shift; and design three benchmarks. …”
Get full text
Journal Article -
3
Aerodynamic optimization and drag minimization for the ultra low cost UAV piquero aerodynamic
Published 2015“…The third segment is a full simulation of the Piquero UAV to determine its lift and drag characteristics. …”
Get full text
Final Year Project (FYP) -
4
Wind tunnel testing of a ducted-fan unmanned aerial vehicle
Published 2011“…The experiments were carried out in a closed-loop wind tunnel with the full-scale MAV at different configurations. Coefficients of lift, drag and pitching moment were first discussed in a simple configuration of varying pitch angle with different wing setups without the propeller motor. …”
Get full text
Final Year Project (FYP) -
5
Microstructure tailoring in hot-pressed silicon carbide
Published 2013“…In the BC system, temperature was varied from 1950 oC to 2050 oC. It was found that full densification was achieved only at 2050 oC. …”
Get full text
Final Year Project (FYP) -
6
-
7
Fabrication and characterization of graphene and carbon nanotube reinforced bioceramic nanocomposites
Published 2020“…Regarding mixing methods, all the ultrasonication mixed and ball milled 1 wt% rGO reinforced HA composites were almost fully densified. …”
Get full text
Thesis-Doctor of Philosophy -
8
Selective laser melting of ceramic particles strengthened stainless steel
Published 2023“…Moreover, undesirable coarse grains and heterogeneous distribution of reinforcements are often observed. …”
Get full text
Thesis-Doctor of Philosophy -
9
Material characterization of additive manufactured metal parts for failure analysis
Published 2019“…SLM fabricated parts have near full density with relatively good mechanical properties. …”
Get full text
Final Year Project (FYP) -
10
Small towing tank for accurate testing of significantly scaled-down ship models
Published 2012“…Flow simulation was completed on the full ship model using the surface capturing approach with the resistance predicted. …”
Get full text
Final Year Project (FYP) -
11
Prediction of Intermittent Fluctuations from Surface Pressure Measurements on a Turbulent Airfoil
Published 2024“…Methods include direct prediction from historical pressure measurements, flow reconstruction followed by forward integration using a full order solver, and data-driven dynamic models in various low dimensional quantities. …”
Get full text
Article -
12
Processing of nanostructured nickel-based magnetic materials
Published 2008“…These alloy systems were processed by ball milling to obtain the compound with grain size of several tens of nanometers in length scale. …”
Get full text
Research Report -
13
Science Overview of the Europa Clipper Mission
Published 2024“…In-situ investigations measure the magnetic field, dust grains, neutral gas, and plasma surrounding Europa. …”
Get full text
Article -
14
Dwarf kingfisher-inspired bionic flapping wing and its aerodynamic performance at lowest flight speed
Published 2023“…The results show amplification of the maximum value for the cycle average lift and drag coefficient as the rotation angle increases. …”
Get full text
Journal Article -
15
An experimental and simulation study of chip transportation behaviour in gundrilling
Published 2017“…From the experiments, terminal velocities of typical gun drill chips at different range of particle Reynolds number were determined to construct the unique drag curve. Based on the findings, a computational fluid dynamic (CFD) numerical model was developed to predict the lateral drag forces with respect to the particle Reynolds number. …”
Get full text
Thesis -
16
Determination of operating point for a propulsive wing UAV using CFD
Published 2018“…CFD simulations were performed using a 2D RANS k-ε turbulence model and the rotating flow was captured using the moving reference frame method. Lift and drag were obtained for different angle of attacks via a control volume analysis of CFD results. …”
Get full text
Final Year Project (FYP) -
17
Partial grounding, identity, and nothing-over-and-aboveness
Published 2023“…I argue that my proposal answers questions concerning the connections between partial grounding, full grounding, and nothing-over-and-aboveness in a motivated way. …”
Get full text
Article -
18
Selective laser melting of 316L stainless steel/ TiC metal matrix composite
Published 2020“…Through an optical microscope, the grain boundaries, porosities, melt pools, columnar grain microstructure were observed. …”
Get full text
Final Year Project (FYP) -
19
Semiconductor oxide for gas sensing applications
Published 2010“…STF02 nanoparticles were synthesized using high energy ball milling technique. Particle size and dispersion of STF02 nanoparticles were then investigated using Zeta sizer test. …”
Get full text
Final Year Project (FYP) -
20