Flexural behaviour and low velocity impact response of hybrid basalt fibre-stainless steel wire mesh laminated composites / by Mohamad Yusuf Salim, 1990-, author 656288, Mohd. Yazid Yahya, supervisor 526309, Shukur Abu Hassan, supervisor 204926, Haris Ahmad Israr Ahmad, supervisor 447070, Ali Farokhi Nejad, 1982-, supervisor 543247, Fakulti Kejuruteraan Mekanikal 8081

The Impact of Process Substitution on Manufacturing Costs: A Comparative Analysis of Sheet Metal Forming versus Extruded Steel Cutting by Talal, Omar

“…The investigation confirms that extruded steel can be a cost-effective alternative to large-scale channel products, providing solutions for industry transition through direct replacement, compatibility-focused redesign, or design guidelines optimized for extruded steel.…”
Get full text

Experimental and numerical studies of pin-ended S960 ultra-high strength steel press-braked channel section columns by Ong, Shao Quan

“…Ultra-high strength steel (UHSS) Grade S960 with the nominal yield stress of 960 MPa, is receiving increasing attention due to its higher strength-to-weight ratio. …”
Get full text

Stainless steel channel sections under combined compression and minor axis bending – part 2 : parametric studies and design by Liang, Yating, Zhao, Ou, Long, Yue-ling, Gardner, Leroy

“…Following the experimental study and finite element (FE) model validation described in the companion paper, numerical parametric studies and the evaluation of design provisions for stainless steel channel sections under combined axial compressive load and minor axis bending moment are presented herein. …”
Get full text

Non-normal distribution of residual flexural strengths of steel fiber reinforced concretes and its impacts on design and conformity assessment by He, Shan, Yang, En-Hua

“…However, variability of residual flexural strengths of steel fiber-reinforced concrete (SFRC) has yet been statistically investigated. …”
Get full text

Multi-physics modeling of melting-solidification characteristics in laser powder bed fusion process of 316L stainless steel by Shan, Xiuyang, Pan, Zhenggao, Gao, Mengdi, Han, Lu, Choi, Joon-Phil, Zhang, Haining

“…In the laser powder bed fusion process, the melting-solidification characteristics of 316L stainless steel have a great effect on the workpiece quality. …”
Get full text

Building 'Tilesy' : a lean tile map editor in unity by Chen, Chin Jieh

Get full text

Optimisation strategies for directed evolution without sequencing by James, J, Towers, S, Foerster, J, Steel, H

High cycle fatigue behavior of 316L stainless steel manufactured via directed energy deposition with varying laser energy by Boey, Kai Jun

“…In this project, 316L stainless steel (SS) blocks was manufactured through DED using varying laser energies. …”
Get full text

Flexural buckling behaviour and residual strengths of S700 high strength steel circular hollow section columns after exposure to fire by Koh, Alicia

“…This paper demonstrates the experimental investigation of the flexural buckling behaviour and residual strengths of cold-formed S700 high strength steel (HSS) circular hollow section (CHS) slender columns after being exposed to fire. …”
Get full text

Flexural-torsional buckling behaviour and resistances of fixed-ended press-braked S690 high strength steel angle section columns by Zhang, Lulu, Liang, Yating, Zhao, Ou

“…The flexural-torsional buckling behaviour and resistances of fixed-ended press-braked S690 high strength steel angle section columns have been studied based on testing and numerical modelling, and reported in this paper. …”
Get full text

Local-flexural interactive buckling of S690 high strength steel slender welded I-section columns: testing, modelling and design by Sun, Yao, Liang, Yating, Su, Andi, Zhao, Ou

“…The present paper reports a thorough experimental and numerical investigation into the local-flexural interactive buckling behaviour and resistances of S690 high strength steel slender welded I-section columns. A testing programme, adopting two S690 high strength steel slender welded I-sections, was firstly conducted and included initial geometric imperfection measurements and ten pin-ended column tests. …”
Get full text

Effects of heat treatment parameters on the microstructure and mechanical properties of laser power bed fusion (LPBF) 316L stainless steel by Sun, Yuheng

“…The 316L austenitic stainless steel (just referred to as 316L here after) is widely used in chemical, biomedical, and marine engineering industries due to its excellent corrosion resistance and mechanical properties. …”
Get full text

Titanium–aluminum–polytetrafluoroethylene coated stainless steel micromold via co-sputtering deposition : replication performance and limitation in hot-embossing by Hardt, David E., Chun, Jung H., Saha, Biswajit, Tor, Shu Beng, Liu, Erjia

“…Stainless steel micromold is an alternative of silicon (Si) micromold in the fabrication of polymeric microfluidic devices because of the brittleness and short lifetime of Si mold. …”
Get full text
Get full text

Machinability assessment when turning AISI 316L austenitic stainless steel using uncoated and coated carbide inserts [electronic resource] / by Rusdi Nur, 1974-, author 599550, Fakulti Kejuruteraan Mekanikal 8081

Visualisation of latent fingerprints on stainless steel knives immersed in a natural outdoor pond using safranin-tinted Candida Rugosa nanoconjugates / by Aida Rasyidah Azman, 1991-, author 609179, Naji Arafat Mahat, supervisor 569255, Roswanira Ab. Wahab supervisor 608904, Hafezul Helmi Hamzah, supervisor 609197, Fakulti Sains 8004

Testing, modelling and design of high strength concrete-filled high strength steel tube (HCFHST) stub columns under combined compression and bending by Zhong, Yukai, Sun, Yao, Tan, Kang Hai, Zhao, Ou

“…This paper presents comprehensive experimental and numerical investigations into the structural behaviour and resistances of high strength concrete-filled high strength steel tube (HCFHST) stub columns under combined compression and bending. …”
Get full text

Part geometry-driven crystallographic texture control in a 3D-printed austenitic steel – a strategy for near-monocrystalline microstructure generation by Chandra, Shubham, Tan, Xipeng, Kumar, Punit, Ramamurty, Upadrasta

“…We propose and employ a novel X-shaped geometry to strengthen the 〈001〉 || z crystallographic texture – distinctive of the electron beam powder-bed fusion technique, for a 3D-printed austenitic stainless steel of type 316 L. The prism angles of the X-shaped parts are varied among 60, 90, and 120 degrees (X-60, X-90, and X-120) to investigate the effect it has on the parts’ properties. …”
Get full text

A study on the use of femtosecond laser to perform surface polishing on a selective laser melting manufactured type 316L stainless steel by Ong, Kenrick Jin Hao

“…In this project, the author studied the use of femtosecond (fs) laser to perform laser polishing on the surface of interest of an additive manufactured 316L Stainless Steel sample. Selective Laser Melting (SLM) was the technique used to produce the sample. …”
Get full text

Kinetics of nitrogen solution from arc plasmas into liquid iron. by Esimai, Charles Nduka.

Subjects: Get full text