-
1
Flank Wear Characterization in Aluminum Alloy (6061 T6) With Nanofluid Minimum Quantity Lubrication Environment Using an Uncoated Carbide Tool
Published 2015“…American Society of Mechanical Engineers (ASME)…”
Get full text
Article -
2
Remaining Tool Life Prediction Based On Force Sensors Signals During End Milling Of Stavax ESR Tool Steel
Published 2017“…American Society of Mechanical Engineers (ASME)…”
Get full text
Get full text
Conference or Workshop Item -
3
Comparative analysis of diesel, diesel-palm biodiesel and diesel-biodiesel-butanol blends in diesel engine
Published 2018“…American Society of Mechanical Engineers (ASME)…”
Get full text
Conference or Workshop Item -
4
Magnetohydrodynamic boundary layer flow and heat transfer of nanofluids past a bidirectional exponential permeable stretching/shrinking sheet with viscous dissipation effect
Published 2019“…American Society of Mechanical Engineers (ASME)…”
Get full text
Article -
5
Heat Transfer Performance of Green Bioglycol-Based TiO2–SiO2 Nanofluids
Published 2021“…American Society of Mechanical Engineers (ASME)…”
Get full text
Article -
6
Flank Wear Characterization in Aluminum Alloy (6061 T6) with Nanofluid MQL Environment using Uncoated Carbide Tool
Published 2015“…American Society of Mechanical Engineers (ASME)…”
Get full text
Article -
7
Optimum Performance Improvements of the Combined Cycle Based on an Intercooler–Reheated Gas Turbine
Published 2015“…American Society of Mechanical Engineers (ASME)…”
Get full text
Article -
8
Influence of chip serration frequency on chatter formation during end milling of Ti6Al4V
Published 2011“…American Society of Mechanical Engineers (ASME)…”
Get full text
Article -
9
The effect of preheating of work on chatter during end milling of medium carbon steel performed on a Vertical Machining Center (VMC)
Published 2003“…American Society of Mechanical Engineers (ASME)…”
Get full text
Article -
10
Development, modeling, and experimental investigation of low frequency workpiece vibration-assisted micro-EDM of tungsten carbide
Published 2010“…American Society of Mechanical Engineers (ASME)…”
Get full text
Article -
11
Impulse response processing of transient heat transfer gauge signals
Published 2008“…ASME (American Society of Mechanical Engineers)…”
Journal article -
12
Heat transfer characteristics of an impingement plate used in a turbine vane cooling system
Published 2001“…American Society of Mechanical Engineers (ASME)…”
Conference item -
13
Uncertainty quantification of leakages in a multistage simulation and comparison with experiments
Published 2017“…American Society of Mechanical Engineers (ASME)…”
Journal article -
14
Compact low-temperature analogue of aero engine firecertification burner
Published 2001“…American Society of Mechanical Engineers (ASME)…”
Conference item -
15
Unsteady conjugate heat transfer modeling
Published 2011“…ASME - American Society of Mechanical Engineers…”
Journal article -
16
Residual elastic strains in autofrettaged tubes: elastic-ideally plastic model analysis
Published 2007“…American Society of Mechanical Engineers (ASME)…”
Journal article -
17
Cooling optimization theory-Part II: Optimum internal heat transfer coefficient distribution
Published 2016“…American Society of Mechanical Engineers (ASME)…”
Journal article -
18
Influence of wave spreading on offshore wind turbine design: a monopile supported DTU 10-MW Turbine Case Study
Published 2024“…American Society of Mechanical Engineers (ASME)…”
Conference item -
19
Aerothermal performance of a winglet at engine representative Mach and Reynolds numbers
Published 2011“…ASME - American Society of Mechanical Engineers…”
Journal article -
20
Cooling optimization theory - Part I: Optimum wall temperature, coolant exit temperature, and the effect of wall/film properties on performance
Published 2016“…American Society of Mechanical Engineers (ASME)…”
Journal article