Partition layout inside a muffler integrated with a thermoelectric generator: Multi-physics analysis and optimal design

Partition layout inside a muffler integrated with a thermoelectric generator: Multi-physics analysis and optimal design

A multi-physics-analysis-based topology optimization (TO) method is proposed to optimally design the internal partition layout of a muffler integrated with a thermoelectric generator (TEG). The basic equations governing the acoustical behavior, heat transfer, and fluid flow in the muffler are introd...

Descripció completa

Dades bibliogràfiques
Autors principals:	Kee Seung Oh, Jin Woo Lee
Format:	Article
Idioma:	English
Publicat:	SAGE Publishing 2022-12-01
Col·lecció:	Journal of Low Frequency Noise, Vibration and Active Control
Accés en línia:	https://doi.org/10.1177/14613484221113339

Ítems similars

Research on characteristics of thermoelectric generator with integrated muffler and catalytic converter
per: Xun Liu, et al.
Publicat: (2022-04-01)

Acoustics of ducts and mufflers /
per: 206483 Munjal, M. L.
Publicat: (2013)

Tuning acoustic performance of multi-chamber hybrid mufflers
per: Van-Hai Trinh
Publicat: (2021-07-01)

Parameter study on the performance of muffler /
per: 290332 Abdull Rahim Abu Bakar
Publicat: (2005)

Study of the combined muffler effectiveness
per: Chichvarina Kristina, et al.
Publicat: (2020-01-01)

Numerical optimization of straight multi-array side-branched mufflers using differential evolution method
per: Min-Chie Chiu
Publicat: (2018-06-01)

Parameter study on the performance of muffler [microfilm] /
Publicat: (2005)

Simulation and experimental investigation of muffler performance
per: Mohiuddin, A. K. M., et al.
Publicat: (2007)

Experimental investigation and simulation of muffler performance
per: Mohiuddin, A. K. M., et al.
Publicat: (2007)

Engineering of a CMC aeronautical muffler
per: Marco Riva, et al.
Publicat: (2024-07-01)

Muffler design optimization through experimental analysis of noise and back pressure
per: Mohiuddin, A. K. M., et al.
Publicat: (2005)

Optimization of four-Chamber and eccentric ellipse mufflers hybridized with multi-Segment perforated/non-perforated tubes
per: Min-Chie Chiu, et al.
Publicat: (2023-06-01)

Influence of partition layouts on speech privacy in open-plan offices
per: Seung-Min Lee, et al.
Publicat: (2024-09-01)

Effect of exhaust thermal parameters on optimal circuit layouts and optimal thermoelectric generator structure used in internal combustion engine
per: Wei He, et al.
Publicat: (2023-07-01)

Parameter study on the performance of muffler [compact disc] /
per: 290332 Abdull Rahim Abu Bakar
Publicat: (2005)

SIMULATION FOR THE PRESSURE LOSS OF AUTOMOTIVE EXHAUST MUFFLER
per: WANG ZhiJie, et al.
Publicat: (2015-01-01)

Study on the Optimized Muffler with Function of PM Filtration for Non-Road Diesel Engines
per: Long Feng, et al.
Publicat: (2022-02-01)

Local Structural Optimization Method Based on Orthogonal Analysis for a Resistant Muffler
per: Rui Li, et al.
Publicat: (2021-01-01)

Experimental study of optimization of thermoelectric modules’ number and layout for waste heat recovery
per: Xiangrong Ma, et al.
Publicat: (2024-05-01)

Research on Module Layout and Module Coverage of an Automobile Exhaust Thermoelectric Power Generation System
per: Weiqi Zhou, et al.
Publicat: (2022-01-01)

Experimental analysis of noise and back pressure for muffler design
per: Mohiuddin, A. K. M., et al.
Publicat: (2008)

Three-pass perforated tube muffler with perforated bulkheads
per: Yiliang Fan, et al.
Publicat: (2016-11-01)

Investigation of baffle configuration effect on the performance of exhaust mufflers
per: Ahmed Elsayed, et al.
Publicat: (2017-09-01)

Acoustic performance of industrial mufflers with CAE modeling and simulation
per: Jeon Soohong, et al.
Publicat: (2014-12-01)

Structural Optimization of a Muffler for a Marine Pumping System Based on Numerical Calculation
per: Houlin Liu, et al.
Publicat: (2022-07-01)

Optimizing the Muffler of a Portable Lawn Mower Engine to reduce Noise Pollution Levels
per: Sh Sedighi, et al.
Publicat: (2021-09-01)

Bending Fatigue Strength and the Effect of Assembling Stress on Fillet Welded Joints of Catalyst Muffler Flange Pipes
per: Gyoko Oh
Publicat: (2017-04-01)

Acoustics of ducts and mufflers with application to exhaust and ventilation system design/
per: 206483 Munjal, M. L.
Publicat: (1987)

Organized Computational Measurement to Design a High-Performance Muffler
per: Mehran Saadabadi, et al.
Publicat: (2023-07-01)

Factors that Influence to Sustainability of MSME Muffler Industry in Purbalingga Regency
per: Faizal Kurniawan, et al.
Publicat: (2020-09-01)

Barrier-free duct muffler for low-frequency sound absorption
per: Cong Gao, et al.
Publicat: (2022-09-01)

Muffler structure improvement based on acoustic finite element analysis
per: Jun Fu, et al.
Publicat: (2019-06-01)

Integrated optimization of thermoelectric systems
per: Schlenker, Aaron Paul.
Publicat: (2020)

Pemanfaatan Panas Buang di Muffler Kendaraan Roda Dua untuk Pembangkitan Listrik Menggunakan Thermoelektrik Generator
per: Sugiyanto, Sugiyanto, et al.
Publicat: (2011)

Exhaust System Muffler Volume Optimization of Light Commercial passenger Car Using Transfer Matrix Method
per: Barhm Mohamad, et al.
Publicat: (2019-03-01)

A comparison between hybrid method technique and transfer matrix method for design optimization of vehicle muffler
per: Mohamad Barhm, et al.
Publicat: (2021-01-01)

Interpreting spatial layouts of nursing homes based on partitioning theory
per: Weiping Cao, et al.
Publicat: (2023-01-01)

Design of phononic crystal for enhancing low-frequency sound absorption in mufflers
per: Yang Bai, et al.
Publicat: (2024-11-01)

Theoretical and Experimental Study on the Transmission Loss of a Side Outlet Muffler
per: Liang Zhang, et al.
Publicat: (2020-01-01)

Law Enforcement of Motorized Vehicles with Muffler Racing by Magelang City Police
per: Damas Reza Kurniadi
Publicat: (2020-01-01)