Study on fatigue crack growth of electron beam selective melting of titanium alloy

Study on fatigue crack growth of electron beam selective melting of titanium alloy

In the application of additive manufacturing, it is inevitable to use some formed parts with a smaller height. The analysis of various mechanical properties of these formed parts is the focus of research. In this paper, the fatigue performance of a titanium alloy specimen with a 10 mm height and ele...

Bibliografiset tiedot
Päätekijät:	Zihao Gao, Shanglei Yang, Xuan Meng, Zhentao Wang, Zeng Peng
Aineistotyyppi:	Artikkeli
Kieli:	English
Julkaistu:	IOP Publishing 2021-01-01
Sarja:	Materials Research Express
Aiheet:	electron beam selective melting titanium alloy fatigue properties secondary cracks
Linkit:	https://doi.org/10.1088/2053-1591/ac2444

Samankaltaisia teoksia

Fatigue growth rate of inclined surface cracks in aluminum and titanium alloys
Tekijä: R.R. Yarullin, et al.
Julkaistu: (2022-04-01)

Low Cycle Fatigue Crack Damage Behavior of TC21 Titanium Alloy with Basketweave Microstructure
Tekijä: Baohua Nie, et al.
Julkaistu: (2022-08-01)

Small fatigue crack growth behavior of TB6 titanium alloy
Tekijä: XU Liang, et al.
Julkaistu: (2019-11-01)

Thermal Fatigue Crack Initiation of Laser Deposited High-temperature Titanium Alloy Ti60A in 20–700 °C
Tekijä: Zhang A.L., et al.
Julkaistu: (2013-08-01)

A Study on Fatigue Crack Closure Associated with the Growth of Long Crack in a New Titanium Alloy
Tekijä: Jiarui Liu, et al.
Julkaistu: (2023-07-01)

The study on the influences of residual stresses on fatigue crack propagation in titanium alloy specimens
Tekijä: A. Zangeneh, et al.
Julkaistu: (2022-12-01)

Effect of morphology of primary a on fatigue crack propagation resistance in a near a heat resistant Titanium alloy
Tekijä: Sumi Y., et al.
Julkaistu: (2020-01-01)

Prediction of Fatigue Crack Growth in Vacuum-Brazed Titanium Alloy
Tekijä: Chou-Dian Huang, et al.
Julkaistu: (2023-11-01)

FATIGUE CRACK GROWTH PERFORMANCE OF TI-6AL-4V TITANIUM ALLOY BY SELECTIVE LASER MELTING
Tekijä: ZHANG HaiYing, et al.
Julkaistu: (2023-12-01)

FATIGUE CRACKING MECHANISMS OF TITANIUM ALLOY VT3-1 IN VERY-HIGH-CYCLE-FATIGUE REGIME
Tekijä: A. A. Shanyavskiy, et al.
Julkaistu: (2016-11-01)

Inclusions in melting process of titanium and titanium alloys
Tekijä: Meng-jiang Cen, et al.
Julkaistu: (2019-07-01)

SIMULATION OF FATIGUE CRACK INITIATION LIFE OF TC4 TITANIUM ALLOY BASED ON ITS MESOSCOPIC PROPERTIES
Tekijä: JIANG Ze, et al.
Julkaistu: (2021-01-01)

Spatial and Direction-Based Characterization of Microstructures and Microhardness of TA15 Titanium Alloy Produced by Electron Beam Melting
Tekijä: Jiangtao Ran, et al.
Julkaistu: (2021-04-01)

Fatigue crack growth behavior of Inconel 718 produced by selective laser melting
Tekijä: R. Konecná, et al.
Julkaistu: (2015-12-01)

Fatigue crack growth behavior of Inconel 718 produced by selective laser melting
Tekijä: R. Konecná, et al.
Julkaistu: (2015-12-01)

Fatigue improvement of electron beam melting-fabricated biomedical Co–Cr–Mo alloy by accessible heat treatment
Tekijä: Daixiu Wei, et al.
Julkaistu: (2018-01-01)

Crack path in aeronautical titanium alloy under ultrasonic torsion loading
Tekijä: A. Nikitin, et al.
Julkaistu: (2015-12-01)

Crack path in aeronautical titanium alloy under ultrasonic torsion loading
Tekijä: A. Nikitin, et al.
Julkaistu: (2016-01-01)

Identification of Relationships between Heat Treatment and Fatigue Crack Growth of αβ Titanium Alloys
Tekijä: Vincent Renon, et al.
Julkaistu: (2019-04-01)

Fatigue-Damage Initiation at Process Introduced Internal Defects in Electron-Beam-Melted Ti-6Al-4V
Tekijä: Robert Fleishel, et al.
Julkaistu: (2023-02-01)

In situ fabrication of a titanium-niobium alloy with tailored microstructures, enhanced mechanical properties and biocompatibility by using selective laser melting
Tekijä: Zhao, Danlei, et al.
Julkaistu: (2020)

Research Progress on Surface Polishing Technology of Powder Bed Fusion Titanium Alloy
Tekijä: ZHOU Di, WU Songquan, LI Ziyang, LIU Lei, YANG Yi, WANG Hao, HUANG Aijun
Julkaistu: (2024-08-01)

Experimental investigation of crack initiation and propagation in high- and gigacycle fatigue in titanium alloys by study of morphology of fracture
Tekijä: M.V. Bannikov, et al.
Julkaistu: (2015-12-01)

Experimental investigation of crack initiation and propagation in high- and gigacycle fatigue in titanium alloys by study of morphology of fracture
Tekijä: M.V. Bannikov, et al.
Julkaistu: (2016-01-01)

The use of various peening methods to improve the fatigue strength of titanium alloy Ti6Al4V manufactured by electron beam melting
Tekijä: Hitoshi Soyama, et al.
Julkaistu: (2018-10-01)

Study of Formed Oxides in IN718 Alloy during the Fabrication by Selective Laser Melting and Electron Beam Melting
Tekijä: Hao Yu, et al.
Julkaistu: (2018-12-01)

Low Cycle Fatigue Behavior of TC21 Titanium Alloy with Bi-Lamellar Basketweave Microstructure
Tekijä: Baohua Nie, et al.
Julkaistu: (2022-06-01)

Dual-Material Electron Beam Selective Melting: Hardware Development and Validation Studies
Tekijä: Chao Guo, et al.
Julkaistu: (2015-03-01)

Fatigue Crack Growth in Maraging Steel Obtained by Selective Laser Melting
Tekijä: Fernando Antunes, et al.
Julkaistu: (2019-10-01)

Fatigue Assessment of Ti–6Al–4V Circular Notched Specimens Produced by Selective Laser Melting
Tekijä: Seyed-Mohammad-Javad Razavi, et al.
Julkaistu: (2017-07-01)

Corrosion fatigue behavior of porous Cu-bearing Ti alloy fabricated by selective laser melting
Tekijä: Ying Sun, et al.
Julkaistu: (2023-03-01)

Study of the Intrinsic Factors Determining the Near-Threshold Fatigue Crack Propagation Behavior of a High-Strength Titanium Alloy
Tekijä: Huan Wang, et al.
Julkaistu: (2025-01-01)

Fatigue Assessment of Selective Laser Melted Ti-6Al-4V: Influence of Speed Manufacturing and Porosity
Tekijä: Unai Segurajauregi, et al.
Julkaistu: (2021-06-01)

Effects of Anisotropic Microstructure and Load Ratio on Fatigue Crack Propagation Rate in Additively Manufactured Ti-6Al-4V Alloy
Tekijä: Elad Chakotay, et al.
Julkaistu: (2024-12-01)

Microstructure and machinability of selective laser melted titanium alloy in micro-milling
Tekijä: Muhammad Rehan, et al.
Julkaistu: (2024-11-01)

Improvement on mechanical properties and corrosion resistance of titanium-tantalum alloys in-situ fabricated via selective laser melting
Tekijä: Zhao, Danlei, et al.
Julkaistu: (2020)

EXPERIMENTAL RESEARCH ON MECHANICAL PROPERTIES OF TITANIUM ALLOY AIRCRAFT STRUCTURE MAINTENANCE PARTS BY ADDITIVE MANUFACTURING
Tekijä: LIU ShiHua, et al.
Julkaistu: (2023-12-01)

Electron beam surface melting of MoSiBTiC alloys: Effect of preheating on cracking behavior and microstructure evolution
Tekijä: Masaya Higashi, et al.
Julkaistu: (2021-11-01)

Effect of Basketweave Microstructure on Very High Cycle Fatigue Behavior of TC21 Titanium Alloy
Tekijä: Baohua Nie, et al.
Julkaistu: (2018-05-01)

New Ti–35Nb–7Zr–5Ta Alloy Manufacturing by Electron Beam Melting for Medical Application Followed by High Current Pulsed Electron Beam Treatment
Tekijä: Maria Surmeneva, et al.
Julkaistu: (2021-07-01)