An Experimental Investigation of Blown-Flap Airfoils
At present, there is significant interest in electrically-powered Urban Air Mobility (UAM) aircraft that can operate in constrained take-off and landing areas (TOLAs) for a variety of missions. While many present designs use vertical take-off and landing (VTOL) capabilities to fulfill this requirem...
| Main Author: | |
|---|---|
| Other Authors: | |
| Format: | Thesis |
| Published: |
Massachusetts Institute of Technology
2022
|
| Online Access: | https://hdl.handle.net/1721.1/139918 |
| _version_ | 1826207257195446272 |
|---|---|
| author | Long, Trevor |
| author2 | Drela, Mark |
| author_facet | Drela, Mark Long, Trevor |
| author_sort | Long, Trevor |
| collection | MIT |
| description | At present, there is significant interest in electrically-powered Urban Air Mobility (UAM) aircraft that can operate in constrained take-off and landing areas (TOLAs) for a variety of missions. While many present designs use vertical take-off and landing (VTOL) capabilities to fulfill this requirement, fixed-wing aircraft utilizing distributed electric propulsion (DEP) to enable blowing across their wings may be able to provide competitive performance while decreasing energy requirements for take-off and landing. In this thesis, the performance of blown-flap wings is investigated to provide both performance estimates and validation data for future work on blowing enabled aircraft.
A quasi 2-dimensional wind tunnel model is used to conduct surveys on both the performance and flow characteristics of propeller blown-flap airfoils. These surveys produced accurate estimates for the cₗ,cₓ,cₘ performance of these wings as a function of the test parameters of angle of attack, 𝛼, flap deflection, 𝛿 subscript f, and blowing power, Δcj. In proper operating regimes, maximum cₗs of over 9.5 were observed, and cₗs over 5 were shown to be easily achievable given proper design. From the surveys of the wake and boundary layer development, the individual propeller slipstreams were found to spread very evenly across the span of the wing, suggesting that 2-dimensional estimates of blown wings may be used for design and analysis of blown wing sections. Stall on the flap upper surface was found to be the primary cause of decreases observed in attainable cₗ as 𝛿 subscript f was increased, and that this stall region was stable and unchanged by increased blowing. Changing the flap geometry was found to delay the onset of this stall and increase performance. Areas of interest moving forward are also identified. |
| first_indexed | 2024-09-23T13:46:48Z |
| format | Thesis |
| id | mit-1721.1/139918 |
| institution | Massachusetts Institute of Technology |
| last_indexed | 2024-09-23T13:46:48Z |
| publishDate | 2022 |
| publisher | Massachusetts Institute of Technology |
| record_format | dspace |
| spelling | mit-1721.1/1399182022-02-08T03:30:02Z An Experimental Investigation of Blown-Flap Airfoils Long, Trevor Drela, Mark Massachusetts Institute of Technology. Department of Aeronautics and Astronautics At present, there is significant interest in electrically-powered Urban Air Mobility (UAM) aircraft that can operate in constrained take-off and landing areas (TOLAs) for a variety of missions. While many present designs use vertical take-off and landing (VTOL) capabilities to fulfill this requirement, fixed-wing aircraft utilizing distributed electric propulsion (DEP) to enable blowing across their wings may be able to provide competitive performance while decreasing energy requirements for take-off and landing. In this thesis, the performance of blown-flap wings is investigated to provide both performance estimates and validation data for future work on blowing enabled aircraft. A quasi 2-dimensional wind tunnel model is used to conduct surveys on both the performance and flow characteristics of propeller blown-flap airfoils. These surveys produced accurate estimates for the cₗ,cₓ,cₘ performance of these wings as a function of the test parameters of angle of attack, 𝛼, flap deflection, 𝛿 subscript f, and blowing power, Δcj. In proper operating regimes, maximum cₗs of over 9.5 were observed, and cₗs over 5 were shown to be easily achievable given proper design. From the surveys of the wake and boundary layer development, the individual propeller slipstreams were found to spread very evenly across the span of the wing, suggesting that 2-dimensional estimates of blown wings may be used for design and analysis of blown wing sections. Stall on the flap upper surface was found to be the primary cause of decreases observed in attainable cₗ as 𝛿 subscript f was increased, and that this stall region was stable and unchanged by increased blowing. Changing the flap geometry was found to delay the onset of this stall and increase performance. Areas of interest moving forward are also identified. S.M. 2022-02-07T15:12:38Z 2022-02-07T15:12:38Z 2021-09 2021-09-16T17:14:05.284Z Thesis https://hdl.handle.net/1721.1/139918 In Copyright - Educational Use Permitted Copyright MIT http://rightsstatements.org/page/InC-EDU/1.0/ application/pdf Massachusetts Institute of Technology |
| spellingShingle | Long, Trevor An Experimental Investigation of Blown-Flap Airfoils |
| title | An Experimental Investigation of Blown-Flap Airfoils |
| title_full | An Experimental Investigation of Blown-Flap Airfoils |
| title_fullStr | An Experimental Investigation of Blown-Flap Airfoils |
| title_full_unstemmed | An Experimental Investigation of Blown-Flap Airfoils |
| title_short | An Experimental Investigation of Blown-Flap Airfoils |
| title_sort | experimental investigation of blown flap airfoils |
| url | https://hdl.handle.net/1721.1/139918 |
| work_keys_str_mv | AT longtrevor anexperimentalinvestigationofblownflapairfoils AT longtrevor experimentalinvestigationofblownflapairfoils |