Sinterable powders from laser driven reactions : final report

Sinterable powders from laser driven reactions : final report

Extremely fine, uniform ceramic powders have been synthesized from Sil4 NH3 and C2H4 gas phase reactants that are heated by absorbing optical energy emitted from a C02 laser. Resulting Si, Si3N4 and SiC powders have been characterized in terms of parameters which are important for densification proc...

Full description

Bibliographic Details
Main Author:	Haggerty, John Scarseth
Published:	Cambridge, Mass. : Massachusetts Institute of Technology, Energy Laboratory, 1981 2011
Online Access:	http://hdl.handle.net/1721.1/60500

Similar Items

Sinterable ceramic powders from laser heated gas phase reactions and rapidly solidified ceramic materials : annual report.
by: Haggerty, John Scarseth
Published: (2011)

Sinterable powders from laser driven reactions : annual report
by: Haggerty, John S., et al.
Published: (2006)

Sinterable powders from laser driven reactions : annual report
by: Haggerty, John S., et al.
Published: (2006)

Sinterable ceramic powders from laser-heated gases
by: Haggerty, John S.
Published: (2005)

Graded index antireflective coatings for glass : final report, September 1978 - February 1982
by: Haggerty, John Scarseth
Published: (2011)

Annual report, April 1981 - May 1982 : laser induced deposition of thin films
by: Gattuso, Todd Richard, et al.
Published: (2011)

Sinterable ceramic powders from laser-heated gases
Published: (2005)

Thermal expansion, heat capacity and structural relaxation measurements in the glass transition region.
by: Haggerty, John Scarseth
Published: (2005)

Improvement of powder management and recycling in laser sintering
by: Wan Yusoff, Wan Ahmad Yusmawiza, et al.
Published: (2011)

Development and optimization of polypropylene-based powders for selective laser sintering
by: Tan, Lisa Jiaying
Published: (2021)

Development of carbon-based polymer nanocomposite powder for selective laser sintering
by: Sim, Derek Jia Shu
Published: (2015)

Development of organically modified montmorillonite/polypropylene composite powders for selective laser sintering
by: Tan, Lisa Jiaying, et al.
Published: (2020)

Development of Aluminium Oxide/polyamide 12 composite powders for direct laser sintering
by: Koh, Wee Kiat
Published: (2018)

Effect of powder calcination on the sintering of hydroxyapatite
by: Tan, C.Y., et al.
Published: (2008)

Constitutive modelling of powder compaction and sintering
by: Cocks, A
Published: (2001)

Densification of metal powder during sintering/
by: 385971 Invensen, V.
Published: (1973)

AFinite Element Model For A Selective Laser Sintering of A Polycarbonate Powder Block
by: Perpustakaan UGM, i-lib
Published: (1997)

Effects of powder synthesis method on the sinterability of hydroxyapatite
by: K. L., Aw, et al.
Published: (2011)

Machining of sintered powder metallurgy materials [microfilm] /
by: Ong, Chin Heng
Published: (2003)

Spark plasma reaction sintering of ZrO2-mullite composites from plasma spheroidized zircon/alumina powders
by: Yu, L. G., et al.
Published: (2012)

Investigation of sintered powder electrodes in electrical discharge machining,
by: Giddens, William E. (William Edgar)
Published: (2011)

Evaluation of spark plasma sintered (SPS) hydroxyapatite powders
by: Chow, Vicky Yuen San.
Published: (2008)

Controlled nucleation and growth process for large grained polycrystalline silicon photovoltaics
by: Danforth, Stephen C., et al.
Published: (2011)

PA12 nylon dust reduction of selective laser sintering reprocessing by optimization of refresh rate and powder handling
by: Muhamad Damanhuri, Amir Abdullah
Published: (2021)

PA12 nylon dust reduction of selective laser sintering reprocessing by optimization of refresh rate and powder handling
by: Ali Detho, Amir
Published: (2021)

Data-driven optimization of OFDA's disaster response capacity: Final Report
by: Goentzel, Jarrod, et al.
Published: (2021)

The effect of powder sintering method on the densification and microstructure of pewter alloys
by: Mohamed Ariff, Tasnim Firdaus, et al.
Published: (2009)

Sintering properties of hydroxyapatite powders prepared using different methods
by: Ramesh, S., et al.
Published: (2012)

Physicochemical properties of hydroxyapatite/montmorillonite nanocomposite prepared by powder sintering
by: Nawang, Rosnah, et al.
Published: (2019)

Spark-plasma-sintering (SPS) of nanostructured titanium carbonitride powders
by: Angerer, P., et al.
Published: (2012)

Towards binder jetting and sintering of AZ91 magnesium powder
by: Salehi, Mojtaba, et al.
Published: (2023)

Selective laser sintering of polymer nanocomposites
by: Wahab, Md Saidin
Published: (2008)

Oriented structure of short fiber reinforced polymer composites processed by selective laser sintering : the role of powder-spreading process
by: Chen, Hui, et al.
Published: (2021)

Final report
by: International Conference on the Trends in the Teaching and Training of engineers (9-13 December, 1968 : Paris)
Published: (1969)

[Final report]
by: Meeting of Representatives of Cultural Research Institutions in Asia (1976 : Tokyo)
Published: (1976)

Final report
by: Regional Seminar on Computers in Education Project (1986 : Pulau Pinang)
Published: (1987)

Final report
by: Subregional Traninig Workshop on Nonformal Environmental Education For Asia (1985 : Serdang)
Published: ([19-)

Final report
by: International Co-ordinating Council of the Programme on Man and the Biosphere (MAB), (1971 Paris)
Published: (1972)

Final Report
by: Expert Panel on the Role of Systems analysis and Modelling Approaches in the Programme on Man and the Biosphere (MAB), (1972 Paris), et al.
Published: (1972)

Final Report
by: Expert panel on Project no1:Ecological Effects of Increasing Human Activities on Tropical and Sub-tropical Forest Ecosys (1972 Paris), et al.
Published: (1972)