Sinterable powders from laser driven reactions : final report

Sinterable powders from laser driven reactions : final report

Extremely fine, uniform ceramic powders have been synthesized from Sil4 NH3 and C2H4 gas phase reactants that are heated by absorbing optical energy emitted from a C02 laser. Resulting Si, Si3N4 and SiC powders have been characterized in terms of parameters which are important for densification proc...

Bibliográfalaš dieđut
Váldodahkki:	Haggerty, John Scarseth
Almmustuhtton:	Cambridge, Mass. : Massachusetts Institute of Technology, Energy Laboratory, 1981 2011
Liŋkkat:	http://hdl.handle.net/1721.1/60500

Geahča maid

Sinterable powders from laser driven reactions : annual report
Dahkki: Haggerty, John S., et al.
Almmustuhtton: (2006)

Sinterable ceramic powders from laser heated gas phase reactions and rapidly solidified ceramic materials : annual report.
Dahkki: Haggerty, John Scarseth
Almmustuhtton: (2011)

Sinterable powders from laser driven reactions : annual report
Dahkki: Haggerty, John S., et al.
Almmustuhtton: (2006)

Sinterable ceramic powders from laser-heated gases
Dahkki: Haggerty, John S.
Almmustuhtton: (2005)

Graded index antireflective coatings for glass : final report, September 1978 - February 1982
Dahkki: Haggerty, John Scarseth
Almmustuhtton: (2011)

Annual report, April 1981 - May 1982 : laser induced deposition of thin films
Dahkki: Gattuso, Todd Richard, et al.
Almmustuhtton: (2011)

Sinterable ceramic powders from laser-heated gases
Almmustuhtton: (2005)

Thermal expansion, heat capacity and structural relaxation measurements in the glass transition region.
Dahkki: Haggerty, John Scarseth
Almmustuhtton: (2005)

Improvement of powder management and recycling in laser sintering
Dahkki: Wan Yusoff, Wan Ahmad Yusmawiza, et al.
Almmustuhtton: (2011)

Development and optimization of polypropylene-based powders for selective laser sintering
Dahkki: Tan, Lisa Jiaying
Almmustuhtton: (2021)

Development of carbon-based polymer nanocomposite powder for selective laser sintering
Dahkki: Sim, Derek Jia Shu
Almmustuhtton: (2015)

Development of organically modified montmorillonite/polypropylene composite powders for selective laser sintering
Dahkki: Tan, Lisa Jiaying, et al.
Almmustuhtton: (2020)

Development of Aluminium Oxide/polyamide 12 composite powders for direct laser sintering
Dahkki: Koh, Wee Kiat
Almmustuhtton: (2018)

Effect of powder calcination on the sintering of hydroxyapatite
Dahkki: Tan, C.Y., et al.
Almmustuhtton: (2008)

Constitutive modelling of powder compaction and sintering
Dahkki: Cocks, A
Almmustuhtton: (2001)

Densification of metal powder during sintering/
Dahkki: 385971 Invensen, V.
Almmustuhtton: (1973)

Machining of sintered powder metallurgy materials /
Dahkki: 335741 Ong, Chin Heng
Almmustuhtton: (2003)

AFinite Element Model For A Selective Laser Sintering of A Polycarbonate Powder Block
Dahkki: Perpustakaan UGM, i-lib
Almmustuhtton: (1997)

Effects of powder synthesis method on the sinterability of hydroxyapatite
Dahkki: K. L., Aw, et al.
Almmustuhtton: (2011)

Machining of sintered powder metallurgy materials [microfilm] /
Dahkki: Ong, Chin Heng
Almmustuhtton: (2003)

Spark plasma reaction sintering of ZrO2-mullite composites from plasma spheroidized zircon/alumina powders
Dahkki: Yu, L. G., et al.
Almmustuhtton: (2012)

Investigation of sintered powder electrodes in electrical discharge machining,
Dahkki: Giddens, William E. (William Edgar)
Almmustuhtton: (2011)

Evaluation of spark plasma sintered (SPS) hydroxyapatite powders
Dahkki: Chow, Vicky Yuen San.
Almmustuhtton: (2008)

Controlled nucleation and growth process for large grained polycrystalline silicon photovoltaics
Dahkki: Danforth, Stephen C., et al.
Almmustuhtton: (2011)

PA12 nylon dust reduction of selective laser sintering reprocessing by optimization of refresh rate and powder handling
Dahkki: Muhamad Damanhuri, Amir Abdullah
Almmustuhtton: (2021)

PA12 nylon dust reduction of selective laser sintering reprocessing by optimization of refresh rate and powder handling
Dahkki: Ali Detho, Amir
Almmustuhtton: (2021)

The effect of powder sintering method on the densification and microstructure of pewter alloys
Dahkki: Mohamed Ariff, Tasnim Firdaus, et al.
Almmustuhtton: (2009)

Sintering properties of hydroxyapatite powders prepared using different methods
Dahkki: Ramesh, S., et al.
Almmustuhtton: (2012)

Physicochemical properties of hydroxyapatite/montmorillonite nanocomposite prepared by powder sintering
Dahkki: Nawang, Rosnah, et al.
Almmustuhtton: (2019)

Spark-plasma-sintering (SPS) of nanostructured titanium carbonitride powders
Dahkki: Angerer, P., et al.
Almmustuhtton: (2012)

Towards binder jetting and sintering of AZ91 magnesium powder
Dahkki: Salehi, Mojtaba, et al.
Almmustuhtton: (2023)

Data-driven optimization of OFDA's disaster response capacity: Final Report
Dahkki: Goentzel, Jarrod, et al.
Almmustuhtton: (2021)

Selective laser sintering of polymer nanocomposites
Dahkki: Wahab, Md Saidin
Almmustuhtton: (2008)

Oriented structure of short fiber reinforced polymer composites processed by selective laser sintering : the role of powder-spreading process
Dahkki: Chen, Hui, et al.
Almmustuhtton: (2021)

Final report
Dahkki: Regional Seminar on Computers in Education Project (1986 : Pulau Pinang)
Almmustuhtton: (1987)

Final report
Dahkki: Subregional Traninig Workshop on Nonformal Environmental Education For Asia (1985 : Serdang)
Almmustuhtton: ([19-)

Final report
Dahkki: International Co-ordinating Council of the Programme on Man and the Biosphere (MAB), (1971 Paris)
Almmustuhtton: (1972)

Final Report
Dahkki: Expert Panel on the Role of Systems analysis and Modelling Approaches in the Programme on Man and the Biosphere (MAB), (1972 Paris), et al.
Almmustuhtton: (1972)

Final Report
Dahkki: Expert panel on Project no1:Ecological Effects of Increasing Human Activities on Tropical and Sub-tropical Forest Ecosys (1972 Paris), et al.
Almmustuhtton: (1972)

Final report
Dahkki: 478509 Asian Regional Seminar on the Promotion of Public Understanding of Science and Technology, Manila, 25th Sept.-2nd Oct. 1972, et al.
Almmustuhtton: (1972)