Powder Mixed Micro Electro Discharge Milling of Titanium Alloy: Analysis of Surface Roughness

Powder Mixed Micro Electro Discharge Milling of Titanium Alloy: Analysis of Surface Roughness

Mostrar outras versões (1)

This paper presents effects of silicon carbide SiC powder concentration on micro EDM parameters on average surface roughness (Ra). The aim is to achieve minimum Ra value on titanium alloy (Ti-6Al-4V) machined with tungsten electrode for various level of concentration of SiC powder and discharge ener...

ver descrição completa

Detalhes bibliográficos
Principais autores:	Ali, Mohammad Yeakub, Adesta, Erry Yulian Triblas, Abdul Rahman, Nur Atiqah, Mohamad Aris, Erniyati
Formato:	Proceeding Paper
Idioma:	English
Publicado em:	2011
Assuntos:	TJ Mechanical engineering and machinery TS Manufactures
Acesso em linha:	http://irep.iium.edu.my/2430/1/ICMMT2011.pdf

Registros relacionados

Powder mixed micro electro discharge milling of titanium alloy: analysis of surface roughness
por: Ali, Mohammad Yeakub, et al.
Publicado em: (2012)

Silicon carbide powder mixed micro electro discharge milling of titanium alloy
por: Ali, Mohammad Yeakub, et al.
Publicado em: (2011)

Micro Electro Discharge Milling for Microfabrication
por: Ali, Mohammad Yeakub, et al.
Publicado em: (2005)

Cutting temperature and surface roughness optimization in CNC end milling using multi objective genetic algorithm
por: Al Hazza, Muataz, et al.
Publicado em: (2012)

Cutting force impact to tool life of CT5015 in high speed machining by applying negative rake angles
por: Adesta, Erry Yulian Triblas, et al.
Publicado em: (2012)

Development of surface roughness prediction model for high speed end milling of hardened tool steel
por: Mohd Ali , Afifah, et al.
Publicado em: (2011)

Influence of process parameters on surface integrity during EDM of mild steel
por: Khan, Ahsan Ali, et al.
Publicado em: (2010)

Influence of electrical discharge machining process parameters on surface micro-hardness of titanium alloy
por: Ndaliman, Mohammed Baba, et al.
Publicado em: (2013)

Comparative study of conventional and micro WEDM based on machining of meso/micro sized spur gear
por: Ali, Mohammad Yeakub, et al.
Publicado em: (2010)

A study of parameters relationship to backcutting phenomena during high speed end milling of AISI H13
por: Adesta, Erry Yulian Triblas, et al.
Publicado em: (2010)

Flank Wear Modeling in High Speed Hard Turning by using artificial Neural Network and Regression Analysis
por: Al Hazza, Muataz Hazza Faizi, et al.
Publicado em: (2011)

Machining Time Simulation in High Speed Hard Turning
por: Adesta, Erry Yulian Triblas, et al.
Publicado em: (2011)

New approach in cost structuring of high speed hard turning
por: Al Hazza, Muataz Hazza Faizi, et al.
Publicado em: (2011)

Tool life in high speed turning with negative rake angle
por: Adesta, Erry Yulian Triblas, et al.
Publicado em: (2011)

The study of the implementation of OHSAS : 18001 at Kulliyyah of Engineering (KOE)
por: Wan Yusoff, Wan Ahmad Yusmawiza, et al.
Publicado em: (2011)

Influence of dielectric fluids on surface properties of electrical discharge machined titanium alloy
por: Mohammed , Baba Ndaliman, et al.
Publicado em: (2013)

Tool life estimation model based on simulated flank wear during high speed hard turning
por: Adesta, Erry Yulian Triblas, et al.
Publicado em: (2010)

Performance evaluation of wire electrical discharge machining on Titanium Alloy
por: Tan, Jun Qi, et al.
Publicado em: (2018)

Development of surface roughness models in end milling titanium alloy Ti-6Al-4V using uncoated tungsten carbide inserts
por: Ginta, Turnad Lenggo, et al.
Publicado em: (2009)

An investigation on low-temperature thermochemical treatments of austenitic stainless steel in fluidized bed furnace
por: Haruman, Esa, et al.
Publicado em: (2012)

A feasibility study on low temperature thermochemical treatments of Austenitic Stainless Steel in Fluidized Bed Furnace
por: Haruman, Esa, et al.
Publicado em: (2011)

Tool vibration due to high speed micro end milling parameters
por: Mohamed, Abd. Rahman, et al.
Publicado em: (2013)

Study of material removal rate and electrode wear ratio for micro electrical discharge milling of AISI 420 and Stavax ESR
por: Mohammad, Yeakub Ali, et al.
Publicado em: (2009)

Study on the effect of nano and micro MoS2 powder in micro-electrical discharge machining
por: Prihandana, Gunawan Setia, et al.
Publicado em: (2011)

Extended enterprise: an extension to supply-chain practice for small to medium enterprise
por: Adesta, Erry Yulian Triblas
Publicado em: (2010)

In-situ worn geometry effect over the surface roughness propagation during micro milling process
por: Nurul Farhana, Mohadzir, et al.
Publicado em: (2020)

Energy cost modeling for high speed hard turning
por: Al Hazza, Muataz Hazza Faizi, et al.
Publicado em: (2011)

Accuracy improvement in nanographite powder-suspended dielectric fluid for micro-electrical discharge machining processes
por: Prihandana, Gunawan Setia, et al.
Publicado em: (2011)

Influence of TaC Powder Additive on electrical discharge machining of stainless Steel
por: Mohd Zain, Zakaria, et al.
Publicado em: (2011)

Fabrication of microfluidic channel using micro end milling and micro electrical discharge milling
por: Ali, Mohammad Yeakub
Publicado em: (2009)

Welding performance of a homemade friction stir welding tool
por: Hilmy, Irfan, et al.
Publicado em: (2014)

Performance of cermet tools : applying negative rake angles high speed machining
por: Adesta, Erry Yulian Triblas, et al.
Publicado em: (2010)

Fabrication of CuSiC composite by powder metallurgy route
por: A. R. , Fatimah Azreen, et al.
Publicado em: (2011)

Empirical modelling of vibration in micro end milling of PMMA
por: Ali, Mohammad Yeakub, et al.
Publicado em: (2013)

Flank wears simulation by using back propagation neural network when cutting hardened H-13 steel in CNC End Milling
por: Al Hazza, Muataz Hazza Faizi, et al.
Publicado em: (2013)

Effects of tool path strategies on surface roughness in high speed milling
por: Abdul Rashid, Muhammad
Publicado em: (2012)

Development of zinc based alloy for solderability
por: Mustafa, Mohd. Yusry, et al.
Publicado em: (2011)

Injection molding parameter optimization of titanium alloy powder mix with palm stearin and polyethylene for green defects using taguchi method
por: Mohamad Nor, Nor Hafiez, et al.
Publicado em: (2009)

Surface Roughness Prediction for CNC Milling Process using Artificial Neural Network
por: M. F. F., Ab Rashid, et al.
Publicado em: (2010)

Taguchi method approach on effect of lubrication condition on surface roughness in milling operation
por: Mohamad Syahmi, Shahrom
Publicado em: (2012)