Optical surface profile tracking for high-resolution strain measurement

Characterization of the mechanical behaviour of materials often requires accurate determination of specimen strain. This paper presents an optical method whereby the surface displacements of a cylindrical specimen undergoing uniaxial loading are measured by tracking the profile of its surface textur...

Bibliografske podrobnosti
Main Authors:	Arthington, M, Siviour, C, Petrinic, N, Elliott, B
Format:	Journal article
Izdano:	IOP Publishing 2011

Podobne knjige/članki

Strain rate dependence of Ti64: Characterisation of mechanical properties up to failure using novel optical techniques
od: Arthington, M, et al.
Izdano: (2009)

Improved materials characterisation through the application of geometry reconstruction to quasi-static and high-strain-rate tension tests
od: Arthington, M, et al.
Izdano: (2012)

Increasing data from high rate characterization experiments using optical reconstruction
od: Siviour, C, et al.
Izdano: (2012)

Cross-section reconstruction during uniaxial loading
od: Arthington, M, et al.
Izdano: (2009)

An Error Analysis into the Use of Regular Targets and Target Detection in Image Analysis for Impact Engineering
od: Jumpasut, A, et al.
Izdano: (2008)

An integrated experimental-numerical method for characterisation of materials at high strain rates
od: Elliott, B, et al.
Izdano: (2007)

High resolution optical measurements of specimen deformation in the split Hopkinson pressure bar
od: Siviour, C, et al.
Izdano: (2009)

TEXTURE DEPENDENCY OF HIGH STRAIN RATE PROPERTIES OF Ti-6Al-4V
od: Wielewski, E, et al.
Izdano: (2009)

Improved predictive modelling of strain localisation and ductile fracture in a Ti-6Al-4V alloy subjected to impact loading
od: Petrinic, N, et al.
Izdano: (2006)

On the correlation between macrozones and twinning in Ti-6Al-4V at very high strain rates
od: Wielewski, E, et al.
Izdano: (2012)

A method for the in situ measurement of evolving elliptical cross-sections in initially cylindrical Taylor impact specimens
od: Wielewski, E, et al.
Izdano: (2010)

Taylor impact experiments on Ti-6Al-4V specimens using 3D geometry reconstruction and instrumented target rods
od: Wielewski, E, et al.
Izdano: (2009)

Compressive deformation of Rohacell foams: Effects of strain rate and temperature
od: Arezoo, S, et al.
Izdano: (2013)

The Effect of Strain Rate, Specimen Geometry and Lubrication on Responses of Aluminium AA2024 in Uniaxial Compression Experiments
od: Li, P, et al.
Izdano: (2009)

Strain rate dependence of a super-elastic NiTi alloy
od: Siviour, C, et al.
Izdano: (2009)

The Strain Rate Dependent Material Behavior of S-GFRP Extracted from GLARE
od: Gerlach, R, et al.
Izdano: (2013)

Experimental characterisation of the strain rate dependent failure and damage behaviour of 3D composites
od: Gerlach, R, et al.
Izdano: (2009)

Quantification of impact energy dissipation capacity in metallic thin-walled hollow sphere foams using high speed photography
od: Li, P, et al.
Izdano: (2011)

Strain rate dependent compressive properties of glass microballoon epoxy syntactic foams
od: Li, P, et al.
Izdano: (2009)

MEASUREMENT OF DEFORMATION IN ALUMINA SAMPLES INDENTED AT HIGH STRAIN RATES
od: Dancer, C, et al.
Izdano: (2011)

Measurements of strain propagation in Hopkinson bar specimens
od: Siviour, C, et al.
Izdano: (2006)

SPECIAL ISSUE ON HIGH STRAIN RATE AND IMPACT LOADING
od: Siviour, C
Izdano: (2010)

High strain rate characterization of polymers
od: Siviour, CR
Izdano: (2017)

High resolution strain measurements in highly disordered materials
od: Mark Sutton, et al.
Izdano: (2021-02-01)

The Meaning and Measure of Vertical Resolution in Optical Surface Topography Measurement
od: Peter J. de Groot
Izdano: (2017-01-01)

Novel measurements of material properties at high rates of strain using speckle metrology
od: Siviour, C, et al.
Izdano: (2009)

High-Spatial-Resolution Dynamic Strain Measurement Based on Brillouin Optical Correlation-Domain Sensors
od: Yahui Wang, et al.
Izdano: (2023-11-01)

Experimentally simulating adiabatic behaviour: capturing the high strain rate compressive response of polymers using low strain rate experiments with programmed temperature profiles
od: Trivedi, AR, et al.
Izdano: (2022)

IMPACT BEHAVIOUR AND ENERGY DISSIPATION IN METALLIC THIN-WALLED HOLLOW SPHERES
od: Li, P, et al.
Izdano: (2011)

Microstructure and x-ray microtomographic characterisation of deformation in electrodeposited nickel thin-walled hollow spheres
od: Li, P, et al.
Izdano: (2013)

Finite element modelling of the mechanism of deformation and failure in metallic thin-walled hollow spheres under dynamic compression
od: Li, P, et al.
Izdano: (2012)

High-Resolution Microbiome Profiling for Detection and Tracking of Salmonella enterica
od: Christopher J. Grim, et al.
Izdano: (2017-08-01)

High strain rate indentation-induced deformation in alumina ceramics measured by Cr3+ fluorescence mapping
od: Dancer, C, et al.
Izdano: (2011)

Damage formation during high strain rate deformation of PBS9501
od: Siviour, C, et al.
Izdano: (2007)

The mechanical response of commercially pure copper under multiaxial loading at low and high strain rates
od: Zhou, J, et al.
Izdano: (2022)

Experimentally simulating adiabatic behaviour: Capturing the high strain rate compressive response of polymers using low strain rate experiments with programmed temperature profiles
od: Akash R. Trivedi, et al.
Izdano: (2022-12-01)

A novel method for pulse shaping of Split Hopkinson tensile bar signals
od: Gerlach, R, et al.
Izdano: (2011)

Experimental analysis of the multiaxial failure stress locus of commercially pure titanium at low and high rates of strain
od: Xu, Y, et al.
Izdano: (2022)

Mechanical behaviour of polymers at high rates of strain
od: Siviour, C, et al.
Izdano: (2006)

High strain rate tensile and compressive effects in glassy polymers
od: Woodworth B.T., et al.
Izdano: (2012-08-01)