Experimental characterisation of the strain rate dependent failure and damage behaviour of 3D composites

Experimental characterisation of the strain rate dependent failure and damage behaviour of 3D composites

Bibliografiska uppgifter
Huvudupphovsmän:	Gerlach, R, Siviour, C, Petrinic, N, Wiegand, J, EDPS
Materialtyp:	Conference item
Publicerad:	2009

Liknande verk

Strain rate dependence of a super-elastic NiTi alloy
av: Siviour, C, et al.
Publicerad: (2009)

An integrated experimental-numerical method for characterisation of materials at high strain rates
av: Elliott, B, et al.
Publicerad: (2007)

The Strain Rate Dependent Material Behavior of S-GFRP Extracted from GLARE
av: Gerlach, R, et al.
Publicerad: (2013)

In-plane and through-thickness properties, failure modes, damage and delamination in 3D woven carbon fibre composites subjected to impact loading
av: Gerlach, R, et al.
Publicerad: (2012)

Experimental characterisation and constitutive modelling of RTM-6 resin under impact loading
av: Gerlach, R, et al.
Publicerad: (2008)

Strain rate dependence of Ti64: Characterisation of mechanical properties up to failure using novel optical techniques
av: Arthington, M, et al.
Publicerad: (2009)

Experimental characterisation of rate-dependent compression behaviour of fibre reinforced composites
av: Pathan, MV, et al.
Publicerad: (2018)

Experimental characterisation of rate-dependent compression behaviour of fibre reinforced composites
av: Pathan Mehtab V., et al.
Publicerad: (2018-01-01)

On the rate dependent behaviour of epoxy adhesive joints: Experimental characterisation and modelling of mode I failure
av: Lissner, M, et al.
Publicerad: (2018)

Improved materials characterisation through the application of geometry reconstruction to quasi-static and high-strain-rate tension tests
av: Arthington, M, et al.
Publicerad: (2012)

Experimentally characterising the temperature and rate dependent behaviour of unfilled, and glass microsphere filled, natural rubber
av: Trivedi, A, et al.
Publicerad: (2023)

Experimental Characterisation of Aluminium 6082 at Varying Temperature and Strain Rate
av: Lemanski, S, et al.
Publicerad: (2013)

TEXTURE DEPENDENCY OF HIGH STRAIN RATE PROPERTIES OF Ti-6Al-4V
av: Wielewski, E, et al.
Publicerad: (2009)

Experimental characterisation and modelling of the strain rate dependent mechanical response of a filled thermo-reversible supramolecular polyurethane
av: Chen, H, et al.
Publicerad: (2022)

Taylor impact experiments on Ti-6Al-4V specimens using 3D geometry reconstruction and instrumented target rods
av: Wielewski, E, et al.
Publicerad: (2009)

Characterisation of damage mechanisms in oxide ceramics indented at dynamic and quasi-static strain rates
av: Dancer, C, et al.
Publicerad: (2019)

Strain rate dependent compressive properties of glass microballoon epoxy syntactic foams
av: Li, P, et al.
Publicerad: (2009)

Rate dependent non-linear mechanical behaviour of continuous fibre-reinforced thermoplastic composites – Experimental characterisation and viscoelastic-plastic damage modelling
av: Matthias Zscheyge, et al.
Publicerad: (2020-08-01)

Compressive deformation of Rohacell foams: Effects of strain rate and temperature
av: Arezoo, S, et al.
Publicerad: (2013)

Experimental analysis of the multiaxial failure stress locus of commercially pure titanium at low and high rates of strain
av: Xu, Y, et al.
Publicerad: (2022)

A comprehensive experimental investigation of the rate-dependent interlaminar delamination behaviour of CFRP composites
av: Chen, Y, et al.
Publicerad: (2023)

An experimental investigation of rate-dependent deformation and failure of three titanium alloys
av: Sarsfield, H, et al.
Publicerad: (2007)

High strain rate characterisation of a polymer bonded sugar
av: Laity, P, et al.
Publicerad: (2006)

Predicting the high strain rate behaviour of particulate composites using time-temperature superposition based modelling
av: Trivedi, AR, et al.
Publicerad: (2021)

Experimentally simulating adiabatic behaviour: capturing the high strain rate compressive response of polymers using low strain rate experiments with programmed temperature profiles
av: Trivedi, AR, et al.
Publicerad: (2022)

The Effect of Strain Rate, Specimen Geometry and Lubrication on Responses of Aluminium AA2024 in Uniaxial Compression Experiments
av: Li, P, et al.
Publicerad: (2009)

On the correlation between macrozones and twinning in Ti-6Al-4V at very high strain rates
av: Wielewski, E, et al.
Publicerad: (2012)

Pressure and temperature dependent dynamic flow and failure behavior of PMMA at intermediate strain rates
av: Zhang, L, et al.
Publicerad: (2021)

Mechanical behaviour of polymers at high rates of strain
av: Siviour, C, et al.
Publicerad: (2006)

Experimentally simulating adiabatic behaviour: Capturing the high strain rate compressive response of polymers using low strain rate experiments with programmed temperature profiles
av: Akash R. Trivedi, et al.
Publicerad: (2022-12-01)

Predicting the high strain rate behaviour of particulate composites using time-temperature superposition based modelling
av: Trivedi Akash R, et al.
Publicerad: (2021-01-01)

Damage formation during high strain rate deformation of PBS9501
av: Siviour, C, et al.
Publicerad: (2007)

A three-dimensional progressive damage model for fibre-composite materials
av: Sosa, J, et al.
Publicerad: (2008)

Characterisation of the high strain rate behaviour of tubular materials
av: Caisso Camille, et al.
Publicerad: (2018-01-01)

Microstructure and x-ray microtomographic characterisation of deformation in electrodeposited nickel thin-walled hollow spheres
av: Li, P, et al.
Publicerad: (2013)

The high strain rate compressive behaviour of polycarbonate and polyvinylidene difluoride
av: Siviour, C, et al.
Publicerad: (2005)

Rate dependent behaviour and dynamic strain localisation of three novel impact resilient titanium alloys: Experiments and modelling
av: Zhang, L, et al.
Publicerad: (2019)

An algorithm for determination of the fracture angle for the three-dimensional Puck matrix failure criterion for UD composites
av: Wiegand, J, et al.
Publicerad: (2008)

Strain rate dependent constitutive modelling of 3D printed polymers
av: Lißner, M, et al.
Publicerad: (2021)

Strain Rate Dependent Constitutive Modelling of 3D Printed Polymers
av: Lißner Maria, et al.
Publicerad: (2021-01-01)