Simulation of plastic injection moulding fishing component using moldex software and D.O.E method [electronic resource] /

Simulation of plastic injection moulding fishing component using moldex software and D.O.E method [electronic resource] /

Project Paper (Sarjana Muda Kejuruteraan (Mekanikal - Pembuatan)) - Universiti Teknologi Malaysia, 2009

Bibliografische gegevens
Hoofdauteurs:	Mohd. Mulyadi Umar, 1986-, Fakulti Kejuruteraan Mekanikal
Formaat:
Taal:	eng
Gepubliceerd in:	2009
Onderwerpen:	Injection molding of plastics

Gelijkaardige items

Simulation of plastic injection moulding fishing component using moldex software and D.O.E method /
door: Mohd. Mulyadi Umar, 1986-, et al.
Gepubliceerd in: (2009)

Simulation plastic injection moulding of fishing reel side cover using moldex software and design of experiment /
door: Mohd. Ariff Abdul Rahman, 1986-, et al.
Gepubliceerd in: (2009)

Simulation of plastic injection moulding of a computer part using moldex software and design of experiment (DOE) /
door: Remnesh Kumar Rajasekaran, 1986-, et al.
Gepubliceerd in: (2010)

Simulation of plastic injection moulding of a facsimile machine component using moldex software and taguchi method /
door: 458366 Muhammad Adham Abdul Wahab, et al.
Gepubliceerd in: (2007)

Simulation of plastic injection moulding of handphone covers using moldex software and classical method /
door: 458345 Liaw, Tsen Kwang, et al.
Gepubliceerd in: (2007)

Simulation of plastic injection moulding of card holders using moldex software and the taguchi method /
door: 322443 Choo, Tien Tean, et al.
Gepubliceerd in: (2007)

Simulation of plastic injection moulding of an air guide using moldex software and the design of experiments /
door: Siti Azeah Mohd. Hashim, 1985-, et al.
Gepubliceerd in: (2008)

Simulation of plastic injection moulding of a computer part using moldex software and design of experiment (DOE) [electronic resource] /
door: Remnesh Kumar Rajasekaran, 1986-
Gepubliceerd in: (2010)

Simulation plastic injection moulding of fishing reel side cover using moldex software and design of experiment [electronic resource] /
door: 352626 Mohd. Ariff Abdul Rahman
Gepubliceerd in: (2009)

Design mould and simulation of plastic injection moulding of water tap using MOLDEX software and the Taguchi method /
door: 325818 Beh, Chee Hong, et al.
Gepubliceerd in: (2007)

Simulation of plastic injection moulding of kancil side mirror cover using moldex software and classical method /
door: 327971 Chan, Uei Nian, et al.
Gepubliceerd in: (2007)

Simulation of plastic injection moulding of a facsimile machine component using moldex software and taguchi method [electronic resource] /
door: 458366 Muhammad Adham Abdul Wahab
Gepubliceerd in: (2007)

Simulation of plastic injection moulding of a car door-handle trim using moldex and design of experiment (DOE) /
door: 389833 Ngu, Ying Kui, et al.
Gepubliceerd in: (2008)

Simulation of plastic injection moulding of an automotive pump impeller using moldex software and taguchi method /
door: 279443 Muhammad Baqir Ibrahim, et al.
Gepubliceerd in: (2007)

Simulation of plastic injection moulding of an air guide using moldex software and the design of experiments [electronic resource] /
door: Siti Azeah Mohd. Hashim, 1985-
Gepubliceerd in: (2008)

Simulation of plastic injection moulding of handphone covers using moldex software and classical method [electronic resource] /
door: 458345 Liaw, Tsen Kwang
Gepubliceerd in: (2007)

Simulation of plastic injection moulding of card holders using moldex software and the taguchi method [electronic resource] /
door: 322443 Choo, Tien Tean
Gepubliceerd in: (2007)

Design mould and simulation of plastic injection moulding of water tap using MOLDEX software and the Taguchi method [electronic resource] /
door: 325818 Beh, Chee Hong, et al.
Gepubliceerd in: (2007)

Simulation of plastic injection moulding of automotive radio antenna by using moldex 3D and design of experiment (DOE) /
door: 326790 Ahmad Sofi Ismail, et al.
Gepubliceerd in: (2008)

Simulation of plastic injection moulding of an automotive pump impeller using moldex software and taguchi method [electronic resource] /
door: 279443 Muhammad Baqir Ibrahim, et al.
Gepubliceerd in: (2007)

Simulation of plastic injection moulding of kancil side mirror cover using moldex software and classical method [electronic resource] /
door: 327971 Chan, Uei Nian
Gepubliceerd in: (2007)

Simulation on sink mark defect of plastic injection moulding of Proton Iswara outer door handle trim using moldex software and D.O.E. classical method /
door: Tan, Sze Ling, et al.
Gepubliceerd in: (2008)

Simulation of plastic injection moulding of a car door - handle trim using moldex and design of experiment (DOE) [electronic resource] /
door: 389833 Ngu, Ying Kui
Gepubliceerd in: (2008)

Simulation of plastic injection molding of cup and hand phone holder using moldex software and design of experiment /
door: Low, Thuan Himm, 1986-, et al.
Gepubliceerd in: (2010)

Simulation of plastic injection molding of cup and hand phone holder using moldex software and design of experiment /
door: Low, Thuan Himm, 1986-
Gepubliceerd in: (2010)

Simulation of plastic injection molding on a thin part product using moldex software and design of experiment /
door: Muhamad Al Baraq Isharudin, 1987-, et al.
Gepubliceerd in: (2010)

Design and optimization of runner system in plastic injection moulding for multy-cavity products by using moldex and design of experiment/
door: Syarizal Iqbal Baba, 1987-, et al.
Gepubliceerd in: (2010)

Simulation of plastic injection moulding of automotive radio antenna by using moldex 3D and design of experiment (DOE) [electronic resource] /
door: 326790 Ahmad Sofi Ismail
Gepubliceerd in: (2008)

Simulation on sink mark defect of plastic injection moulding of Proton Iswara outer door handle trim using moldex software and D.O.E. classical method [electronic resource] /
door: 308603 Tan, Sze Ling
Gepubliceerd in: (2008)

Simulation of plastic injection moulding of automotive part using moldflow & D.O.E /
door: Raja Suhada Raja Muda, 1988-, author, et al.
Gepubliceerd in: (2011)

Simulation of plastic injection molding on a thin part product using moldex software and design of experiment [electronic resource] /
door: Muhamad Al Baraq Isharudin, 1987-
Gepubliceerd in: (2010)

Design and optimization of runner system in plastic injection moulding for multy-cavity products by using moldex and design of experiment [electronic resource] /
door: Syarizal Iqbal Baba, 1987-
Gepubliceerd in: (2010)

Simulation of plastic injection moulding of family mould using moldflow and design of experiment /
door: Mohd. Najib Mohd. Badri, 1978-, et al.
Gepubliceerd in: (2010)

Development of a plastic injection mould /
door: 312716 Lim, Seng Giam, et al.
Gepubliceerd in: (1994)

Plastics injection moulding in the 1990s
Gepubliceerd in: (1990)

Simulation of plastic injection moulding of fishing reel support arm using moldflow software and design of experiments /
door: Mohd. Azlan Suhaimi, 1985-, et al.
Gepubliceerd in: (2009)

Simulation of plastic injection moulding part using moldflow and design of experiment /
door: Shamsul Azwan Halim, 1975-, et al.
Gepubliceerd in: (2010)

Simulation of plastic injection moulding of automotive part using moldflow & D.O.E [electronic resource] /
door: Raja Suhada Raja Muda, 1988-, author
Gepubliceerd in: (2011)

Injection moulding of plastic components : a guide to efficiency, fault diagnosis and cure/
door: 233146 Bown, John
Gepubliceerd in: (1979)

Simulation of plastic injection moulding part using moldflow and design of experiment [electronic resource] /
door: Shamsul Azwan Halim, 1975-, et al.
Gepubliceerd in: (2010)